background image

 

POWX240 

EN

 

Copyright © 2015 VARO 

p a g e

 | 

6

 

 

www.varo.com 

 

Unplug the machine and clean the table before leaving the work area. 

 

Wear protective glasses, dust mask, ear defenders, work gloves and protective-sliding 
shoes. 

 

Keep the table flat and do not scratch or press the table. 

 

Do not put hands anywhere near the blade whilst it is rotating. 

 

Do not attempt to free a jammed blade without first switching off or removing the plug from 
the mains power supply. 

 

Do not cut small workpiece and also do not use for a purpose not intended. 

 

Keep water full in the tank when you operate the cutter. 

 

Do not use any solvents for instead water in this tool. 

6.1 

Power supply 

 

This tile saw must be connected to an earthed 230V - 50Hz power source. 

 

This power source must be secured by a 16A fuse. 

 

Your machine is supplied with a 30mA residual current device to protect the user against 
electric shock. 

 

It can only protect you when the power mains to which the tool is plugged is properly 
grounded. 

 

Have the proper outlet installed by a qualified electrician. 

 

Check with a qualified electrician or service personnel if the grounding instructions are not 
completely understood, or if in doubt as to whether the tool is properly grounded. 

6.2 

Using an extension lead 

 

The use of any extension lead will cause some loss of power. 

 

To keep this to a minimum and to prevent overheating and motor burn-out, ask advice 
from a qualified electrician to determine the minimum wire size of the extension lead. 

 

The extension lead should be equipped with an earthed type plug that fits the power 
supply outlet at one end, and with an earthed type socket that fits the plug of the machine 
at the other end. 

7  ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS 

 

Warning!

 The laser beam potentially causes severe eye damage. Never look or stare 

directly into the laser beam.  

 

During use, do not point the laser beam at people, directly or indirectly through reflecting 
surfaces.  

 

This laser complies with class 2 according to EN 60825-1:2001. The unit includes no 
servicing components. Do not open the housing for any reason. If the unit is damaged, 
have the damage repaired by an authorized repair agent.   

 

Attention 
Laser beam 
Do not stare into the beam 
laser class 2 

 
Laser class : class 2 
Laser wave length : 650 nm 
Laser output : ≤1 mW 
 

The laser on this machine is equiped with 2 AAA batteries. 

Содержание POWERplus POWX240












Отзывы: