background image

 

POWX1190 

EN

 

Copyright © 2020 VARO NV 

S t r a n a

 | 

6

 

www.varo.com 

 

Never start up a hammer tool until it pressed against a workpiece (wall, ceiling, etc.). 

 

When you are finished, unplug the hammer drill from the electric supply and remove the 
chisel or drill bit Irom the machine. 

 

Always disconnect the hammer drill Irom the electric supply before you change a chisel or 
drill bit. 

 

Protect your eyes and other workers from flying particles and splinters. Wear a helmet! Set 
up partition walls! 

 

Wear work gloves to protect fingers from bruising and grazing. 

 

Vibrations can injure the hand-arm system. Keep exposure to vibrations as short as 
possible. 

 

Always lead the mains cable away backwards from the device. 

 

Store the device where it is inaccessible to children. 

 

When carrying out work, always hold the device with both hands and ensure that you have 
a stable standing position. 

7  BEFORE USING THE TOOL FOR THE FIRST TIME 

 

Examine the place where the device is to be used for hidden electrical cables, gas and 
water pipes using a pipe finding device. 

 

Before connecting to !he mains, ensure care that the mains voltage corresponds to the 
details on the rating plate. 

 

Ensure that the power switch is in the OFF position.  If the plug is connected to a mains 
while the power switch is in the ON position, the power tool will start operating 
immediately, which could cause serious accidents. 

 

When the work area is removed from the power source, use an extension cord of sufficient 
thickness and rated capacity.  The extension cord should be kept as short as practicable. 

7.1 

Fitting and changing tools (Fig. 1) 

The device is equipped with a SDS-Max attachment system. 

 

Clean tools and grease with a thin layer of machine grease before fitting. 

 

Pull back fastening sleeve and hold. 

 

Push and rotate the dust-free tool into the tool holder as far as it will go. The tool will lock 
automatically. 

 

Check that it has locked by pulling the tool 

7.2 

Removing SDS-Max tool 

Pull back fastening sleeve, hold and remove tool. 

Accessories can be hot after use.  Don’t touch the tip of accessory by hand!  
Please always use protective floves to remove accessory. 

8  OPERATION 

8.1 

Switching ON/OFF 

 

Switching on: 

 Press the operating switch (9). 

 

Switching off: 

 Release the operating switch(9) 

8.2 

Variable speed 

The speed can be adjusted between Min. and Max. speed through rotating the speed control 
dial (13) from 1 to 6.  
It will accelerate when adjust the controller from 1 to 6.  If dial 6 to 1, the machine slow down. 
choose the right speed according to the work piece. 

Содержание Powerplus POWX1190











Отзывы: