VARO POWERPLUS POWEG8012 Скачать руководство пользователя

Страница: 10 / 14

POWEG8012

P a g e

www.varo.com

10.3

Change/adjustment of the spark plug

Attention! Worn-out spark plugs or too large distance between breaker
contacts decrease the engine performance.

▪

Turn the unit off.

▪

Disconnect the sparkplug cable from the spark plug.

▪

Unscrew counterclockwise the spark plug with a spark plug key. Do not use any other tool
in order to prevent any damage.

▪

Use a control template (available at specialized shops) and check the distance between
the breaker contacts. The distance must be 0.635 mm.

▪

If necessary, correct the distance by carefully bending the ignition arch of the spark plug.

▪

Clean the spark plug with a wire brush.

▪

Insert a cleaned and adjusted spark plug or replace the damaged one by a new one.

▪

Reconnect the spark plug cable.

10.4

Carburetor adjustment

The carburetor was adjusted to optimum performance already during production. If the
carburetor requires readjustment, have it done at a specialized expert repair shop.

11 TROUBLESHOOTING

PROBLEM

CHECK

STATUS

CAUSE

REMEDY

Engine
cranks-
starts
hard/does
not start

▪

Fuel at
carburetor

▪

No fuel at
carburetor

▪

Fuel strainer
clogged

▪

Fuel line
clogged

▪

Clean or
replace

▪

Clean or
replace

▪

See dealer

▪

Fuel at
cylinder

▪

No fuel at
cylinder

▪

Carburetor

▪

See dealer

▪

Muffler wet
with fuel

▪

Fuel mixture
too rich

▪

Open choke

▪

Clean or
replace air filter

▪

Adjust
carburetor

▪

Spark at end
of plug wire

▪

No spark

▪

Power switch
off

▪

Electrical
problem

▪

Interlock
switch

▪

Turn switch on

▪

See dealer

▪

See dealer

▪

Spark at
plug

▪

No spark

▪

Spark gap
incorrect

▪

Covered with
carbon

▪

Fouled with
fuel

▪

Plug defective

▪

Adjust to
0.65mm

▪

Clean or
replace

▪

Clean or
replace

▪

Replace plug

Engine runs
but dies or
does not
accelerate
properly

▪

Air filter

▪

Air filter dirty

▪

Normal wear

▪

Clean or
replace

▪

Fuel filter

▪

Fuel filter
dirty

▪

Contaminants
residues in
fuel

▪

Replace

Содержание POWERPLUS POWEG8012















Результаты поиска

Содержание POWERPLUS POWEG8012

Отзывы:

Похожие инструкции для POWERPLUS POWEG8012

Бренды по названию

Популярные бренды

VARO POWERPLUS POWEG8012, Руководство пользователя

Результаты поиска

Содержание POWERPLUS POWEG8012

Отзывы:

Похожие инструкции для POWERPLUS POWEG8012

Бренды по названию

Популярные бренды