background image

 

POWDP1570 

EN

 

Copyright © 2018 VARO 

P a g e

 | 

9

 

www.varo.com 

9.6 

Switching ON/OFF 

 

Switching on: 

 Press the operating switch (5). 

 

Switching off: 

 Release the operating switch (5). 

9.6.1 

Switch lock (Fig. 4) 

The switch trigger can be locked in the centre position. 
This helps to reduce the possibility of accidental starting when not in use. To lock the switch 
trigger, place the direction of rotation selector in the centre position. 

9.6.2 

Direction of rotation (Fig. 5) 

Direction of rotation is controlled by the direction of rotation selector located above the switch 
trigger. 

9.6.2.1 

Clockwise rotation: 

Right: To select forward rotation, release the on/off switch and push the forward/reverse lever 
to the left side of the tool. 

9.6.2.2 

Anticlockwise rotation: 

Left: To select reverse rotation, push the lever to the right side of the tool. 

9.6.3 

Variable speed 

This tool has a variable speed switch that delivers higher speed and torque with increased 
trigger pressure. 
Speed is controlled by the amount of switch trigger depression. 

9.7 

Handle attachment (Fig. 6) 

For reasons of safety, only use the hammer drill with handle attachment. 
You will be able to obtain a safe body position when working by rotating the handle 
attachment. Loosen and turn the handle attachment in an ant-clockwise direction. Slip loop 
onto the neck of the housing tool and position the handle, then tighten the handle attachment. 

9.8 

Depth stop 

Loosen the handle attachment and place the straight part of the depth stop in the hole. Adjust 
the depth stop and retighten the handle attachment. 

9.9 

Dust collection device 

Before carrying out hammer-drilling work vertically overhead pull dust collecting device over 
the drill bit. 

9.10 

Function mode selector 

 

Hammer/ drill mode: 

Drill in masonry, concrete and natural stone.  
Don’t use the hammer drill function for ceramic tile or others material can not 
withstand impact energy. 

 

Chiselling mode:  

Chisel in masonry, concrete and natural stone.  

Содержание Powerplus POWDP1570













Отзывы: