background image

 

POWDP15200 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

8

 

www.varo.com 

8.8 

TPR soft grip 

Your cordless drill is equipped with TPR soft grip and protective parts.  TPR (Thermoplastic 
rubber) is elastic, chock absorbing and environmental friendly (recyclable). 

9  OPERATION 

9.1 

Charging the battery pack 

The battery pack for this tool is supplied in a low charge condition to prevent possible 
problems, therefore, you have to charge the battery before first use. 

Note: Batteries will not reach full charge the first time they are charged. 
Allow several cycles for the item to fully charge. The battery should only be 
charged indoors. 

After normal use, about 1 hour of charging time is required for the battery to be fully charged. 
The battery pack will become slightly warm while charging, this is normal and does not 
indicate a problem. 
Do not place the charger in an area of extreme heat or cold. Best is at normal room 
temperature. When the battery becomes fully charged, unplug your charger from the power 
supply and remove the battery pack from the charger. 
Note: 
1. 

Allow the battery pack to cool completely before charging 

2. 

Inspect the battery pack before charging, do not charge a cracked or leaking battery 
pack. 

9.1.1 

Charging indication (Fig 1) 

Connect the charger to the power outlet socket 

 

Solid green: ready to charge 

 

Flickering red: charging 

 

Solid green: charged 

 

Solid green and red: battery or charger damaged 

Note:If the battery does not fit properly, disconnect it and confirm that the 
battery pack is the correct model for this charger as shown on the 
specification chart. Do not charge any other battery pack or any battery 
pack that does not securely fit the charger. 

1. 

Frequently monitor the charger and battery pack while connected 

2. 

Unplug the charger and disconnect it from the battery pack when finished. 

3. 

Allow the battery pack to cool completely before using it. 

4. 

Store the charger and battery pack indoors, out of reach of children. 

NOTE: If battery is hot after continuous use in the tool, allow it to cool down 
to room temperature before charging. This will extend the life of your 
batteries. 

NOTE: Remove battery pack from charger stand which use your thumb or 
fingers, press the battery

’s release button in and pull the battery pack off at 

the same time. 

 

 

Содержание Powerplus POWDP15200















Отзывы: