MODE D'EMPLOI
9 87-900-870-01 (
E
)
INDICATIONS GENERALES
Cet appareillage a été conçu en vue d'une utilisation
professionnelle. Il est conseillé à l'utilisateur de lire
attentivement cette notice d'instructions ainsi que toute
autre indication supplémentaire fournie par Varian,
avant l'utilisation de l'appareil. Varian décline par
conséquent toute responsabilité en cas d'inobservation
totale ou partielle des instructions données, d'utilisation
incorrecte de la part d'un personnel non formé,
d'opérations non autorisées ou d'un emploi contraire
aux réglementations nationales spécifiques. Le
contrôleur de la série Turbo-V 70 est un convertisseur
de fréquence, contrôlé par un microprocesseur, réalisé
avec des éléments à l'état solide et ayant des
capacités d'autodiagnostic et d'auto- protection. Le
contrôleur pilote les pompes de la série Turbo-V 70
(par un processus subdivisé en dix pas) lors de la
phase de mise en marche, en contrôlant la tension et le
courant par rapport à la vitesse atteinte par la pompe. Il
incorpore l'ensemble de circuits nécessaire au
fonctionnement automatique des pompes de la série
Turbo-V 70. Un connecteur auxiliaire permet de
disposer des commandes de mise en marche et d'arrêt
de la pompe à distance, des signaux indiquant l'état
opérationnel de la pompe, des commandes de mise en
marche et d'arrêt de la pompe à pré-vide ainsi que de
signaux de blocage (pour interrupteurs à pression,
interrupteurs de contrôle du flux de l'eau, etc.). Les
paragraphes suivants donnent toutes les indications
nécessaires à garantir la sécurité de l'opérateur
pendant l'utilisation de l'appareillage. Des
renseignements plus détaillés se trouvent dans
l'appendice "Technical Information".
Cette notice utilise les signes conventionnels
suivants:
!
Les messages de danger attirent l'attention de
l'opérateur sur une procédure ou une manoeuvre
spéciale qui, si elle n'est pas effectuée correctement,
risque de provoquer de graves lésions.
ATTENTION!
Les message d'attention apparaissent avant certaines
procédures qui, si elles ne sont pas observées,
pourraient endommager sérieusement l'appareillage.
NOTE
Les notes contiennent des renseignements importants,
isolés du texte.
EMMAGASINAGE
Pendant le transport et l'emmagasinage des
contrôleurs, il faudra veiller à respecter les conditions
environnementales suivantes:
•
empérature: de - 20 °C à + 70 °C
•
humidité relative: de 0% à 95 % (non condensante).
PREPARATION POUR L'INSTALLATION
Le contrôleur est fourni dans un emballage de
protection spécial; si l'on constate des marques de
dommages pouvant s'être produits pendant le
transport, contacter aussitôt le bureau de vente local.
Pendant l'opération d'ouverture de l'emballage, veiller
tout particulièrement à ne pas laisser tomber le
contrôleur et à ne lui faire subir aucun choc. Ne pas
jeter l'emballage dans la nature. Le matériel est
entièrement recyclable et il est conforme aux directives
CEE 83/399 en matière de protection de
l'environnement.
Emballage du contrôleur
Le Contrôleur modèle 969-9506 est fourni par Varian
déjà pré-équipé pour une tension d'alimentation de 120
Vca.
S'il est nécessaire de changer la tension d'alimentation,
procéder de la façon suivante:
−
Débrancher le câble du connecteur P17 du
contrôleur.
−
Sélectionner la tension d'alimentation voulue sur le
tableau gauche.
−
S'assurer que la tension correcte a été
sélectionnée, puis reconnecter le câble au
connecteur P17.
DANGER!