Vari Lite VL4000 BeamWash Luminaire Скачать руководство пользователя

Страница: 27 / 190

0 2 . 9 7 0 4 . 6 0 1 0 0

HAPTER

Routine Maintenance

This chapter contains test, service, and standard maintenance procedures.

• Equipment Handling

• Troubleshooting

• Routine Maintenance

Note:

This manual is a preliminary release version. Additional maintenance

procedures and information will be released in an updated version of the manual.

WARNING:

All maintenance procedures are to be performed with power

removed from the luminaire. Never remove cover or backcap while lamp is in oper-
ation.

WARNING:

Maintenance, repairs, and adjustments should only be performed by

a qualified, factory-trained service technician at an Authorized VARI

❋

LITE

Service Center.

Содержание VL4000 BeamWash Luminaire































































































































































































Результаты поиска

Содержание VL4000 BeamWash Luminaire

Отзывы:

Похожие инструкции для VL4000 BeamWash Luminaire

Бренды по названию

Популярные бренды

Vari Lite VL4000 BeamWash Luminaire, Руководство по обслуживанию

Результаты поиска

Содержание VL4000 BeamWash Luminaire

Отзывы:

Похожие инструкции для VL4000 BeamWash Luminaire

Бренды по названию

Популярные бренды