background image

 

Technical Manual: TM20514-10 
AmpMC 3-field Series 
Revision: 3.0 

Date of release: 2019-01-09

 

7/24 

www.vareximaging.com

 

2. 

Product description 

 

Intended use 

The device is intended to be used in medical diagnostic applications with restrictions to human 
diagnostics. The device is intended to be used as accessory of an X-ray system in a professional 
healthcare facility environment. The device is intended to amplify and integrate the output signal of a 
SolidStateMC to the AEC-module of an X-ray generator. The limitations of use are specified in §2.8. 
The device is not intended to be used in fluoroscopy applications; near active HF Surgical Equipment 
or in the RF shielded room of a system for magnetic resonance imaging, where the intensity of 
Electromagnetic Disturbances is high. 
Use, other than above, is identified as abnormal use. 
The device is intended as an internal component of an X-ray system. The intended user is defined as 
the S

ERVICE 

P

ERSONNEL

 of an X-ray system.

 

 

Description of the device§§ 

The purpose of the Automatic Exposure Control (AEC) of an X-ray system is to obtain the correct 
image contrast by measuring the radiation quantity striking the film or detector. 
To result in a high-quality image, the AEC’s exposure end switch will stop generating X-rays 
automatically when the demanded radiation dose on the detector is reached.  

 

Principle of operation 

The AmpMC main functions are: 

 

The conversion of electrical current from a SolidStateMC to a voltage ramp. The voltage ramp 
signal is proportional to the received dose of the SolidStateMC. 

 

To receive field-select signals (from operator via console and generator) and use the correct 
field of the SolidStateMC as the incoming signal.  

A SolidStateMC serves as a measuring device for X-ray radiation with semiconductor components 
(photodiodes) as actual sensors. The ionizing effect of X-ray produces a small electrical current in the 
photodiodes and this current is lead to an AmpMC.  
The AmpMC converts the small current to a voltage signal that is proportional to the X-ray dose rate, 
this signal is integrated and presented as a ramp signal to the AEC controller board inside the 
generator and therefore represents a value for the image density. 

 

There is no signal available for external use about the status of the device. 

 

Classifications 

Subject 

Classification 

Reference 

CE 

IIB 

93/42/EEC 

Electrical safety  

None 

IEC 60601-1 

Electromagnetic Compatibility 
intended environment 

Professional 
healthcare facility 
environment 

IEC 60601-1-2 

Mode of operation 

Continuous 

IEC 60601-1 

Ingress protection  

IP2X 

IEC 60529 

Protection 

No 

IEC 60601-1 table 6 

Not intended for use in Oxygen Rich environment. 

Not suitable for Sterilization. 

Содержание Claymount AmpMC 3-field Series

























Отзывы: