background image

Adjust Air & Water Ratio (FIG 7) 

1. Adjust the air and water via the variable valves on the 

side of the unit to create the desired e

ect size and type.

2. Take into account any water accumulation on the 

surrounding areas. The 6b is designed to create a full 
plume of flame e

ect while maintaining a dry surrounding 

area thus creating an e

ect that is safe to use near other 

equipment. 

3. NOTE: If the Air supply is adjusted too low, the internal 

piston mechanism of the 6b’s nozzle will activate and both 
air and water output will be stopped.  To restore air and water output, increase air 
supply.

4. NOTE: Increasing the amount of air in relation to the amount of water will result in a 

narrower, thinner e

ect, and will result in less or no water collecting on the 

surrounding area.

5. NOTE: Increasing the amount of water in relation to the amount of air will result in a 

wider, thicker e

ect, but could cause water to collect on surrounding area.

6. NOTE: Due to di

erences in relative humidity the e

ect may need to be adjusted for 

more or less water.  

Nozzles (FIG 8) 

1. Nozzle tips may be changed to create di

erent e

ects. Use 12mm and 14mm 

wrenches to remove and replace nozzle tips.

2. It may be necessary to clear a blockage if the nozzle becomes clogged.  Use a 

14mm wrench to remove the nozzle tip, and inspect for debris.  

3. A plume that is wide and not particularly tall is a sign that debris has entered the 

nozzle and most likely collected on the inside of the tip.  Remove the tip to clean 
out debris.  

Storing the Unit 

Be sure to drain remaining water from the unit before storage. 

1. Briefly connect the air supply to the water in on the VF6b unit. This creates a 

bubble of air to clear the water line.

2. Disconnect the air supply from the unit and reconnect correctly.  Run the unit using 

ONLY the air channel. Leave the water channel at 0.  Run the unit until all of the 
water is cleared from the e

ect plume.  

Page   of 

9

12

Rev. 2.0 11/20

FIG. 7

Содержание VF6b













Отзывы: