background image

25 

 

3.5 Other 

Options 

All selectable via a display (either Hard Wired or Hand held)

 

 

Feed With Drain 

Used to lower the temperature of the drain water.

 

 

Frost Protectiion 

When this is activated the unit will operate, at a preset demand level, if the temperature surrounding the unit falls 
below a preset level, to prevent the pipework from freezing.

 

 

It is enabled by setting “frost demand” (via keypad/display) to >0 (it I disabled by setting “frost demand” to 0). 
However the unit will not operate unless “frost demand” is set above the unit minimum demand level. Minimum 
demand level for LE units is 21% and for LEP units it is 10%. 
Frost demand is fully adjustable between 0 & 50%.

 

 

Timed Drain down. 

Used to drain all the water from the cylinder if the unit remains on standby for longer than a preset (but adjustable) 
time period.

 

 

For information on setting these options please see the display manual.

 

 

3.6 

Use with LRO unit. 

For information on setting up a system with a Vapanet Reverse Osmosis unit please see the doccumentation 
supplied with the LRO unit. 

 

The following light sequences may also appear on the LR unit fascia if an LRO unit is supplying the feed water 
supply:- 

User LED 1 Sequence:

 

 

 

Meaning: 

Amber (off) Green (off):  

 

 

LRO in “Shutdown” Mode (Switched off or EPO/security circuit open) 

Amber (off) Amber (off) Green 

 

LRO unit not responding. (LR unit “Fault” relay will make). 

Amber (off) Amber (off) Amber (off) Green 

LRO unit in “Fault” condition. (LR unit “Fault” relay will make). 

Содержание LR10













































Отзывы: