background image

www.vanco1.com

 800-626-6445

10

TROUBLE-SHOOTING

1.  If you do not get audio and video, access the “setup” menu on the TV to adjust the audio and video 

settings. If the HDMI control circuit cannot establish a handshake, then there usually will be no audio or 
video in addition to a blue or black screen with a statement similar to “this protocol not supported” or 
“weak signal”.

2.  If the above mentioned messages display, reset the receiver by disconnecting the power supply. You can 

also disconnect all of the HDMI and power cables, wait 15 minutes for any voltages to decay and then 
reconnect all of the cables.

3.  If you are still encountering issues, attempt the “hot-plug” concept. With all of the HDMI cables 

disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco 
unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from 
the receiver into it. This activates all of the devices in corresponding order and results in a signal being 
plugged into a device that is on and will attempt to connect the signal.

4.  Most of the major source and display manufacturers employ a proprietary control channel to communicate 

between devices from the same manufacturer. Sometimes this can interfere with the HDMI control circuit 
or the authentication of the signal. Call the manufacturer if you experience this issue. Sometimes a player, 
an audio/video receiver, or a cable/satellite box may not have the latest software update, usually this can 
be downloaded from the manufacturer’s website.

SAFETY AND NOTICE
The 280595 has been tested for conformance to safety regulations and requirements, and has been certified 
for international use. However, like all electronic equipments, the 280595 should be used with care. Please 
read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of 
damage to the unit.

•  Follow all instructions and warnings marked on this unit.
•  Do not attempt to service this unit yourself, except where explained in this manual.
•  Provide proper ventilation and air circulation and do not use near water.
•  Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
•  Use only the power adapter and power cords and connection cables designed for this unit.
•  Do not use liquid or aerosol cleaners to clean this unit. 
•  Always unplug the power to the device before cleaning.

Содержание 12x3 Multi-Function Switch/Scaler













Отзывы: