Van Isle Water Clack WS1 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 9

Van Isle Water Clack WS1 Скачать руководство пользователя страница 5

9. Now you can plug in the controller. See the accompanying Clack WS1 Basic Controller Programing Instructions

on how to program. Your filter is already programmed for the size of conditioner you have. It will regenerate

based on the amount of water which can be treated measured in gallons or every 6 days which ever comes first.

The only thing you should have to set is the time of day and possibly the time of regeneration. The default for

this is 2:00am which is a good time for regeneration unless you have more than one conditioner. They should

not regenerate at the same time. Water should not be used while the conditioner is regenerating. If you taste

salty water after regeneration, run the water until it clears up.

10. Now you are ready to turn on the water. Turn on the water and leave the filter on bypass and check for

leaks.

11. Press the REGEN button for several seconds which will start a manual backwash. Once controller is in

backwash unplug it so it will stay in backwash as long as necessary.

Fig. 1 Auto Backwash HIM Filter System Flow Diagram (Not to Scale)

«
...
3
4
5
6
7
...
»

Содержание Clack WS1










Отзывы:

Нет отзывов