VALUEPLANES MILES M.2H HAWK MAJOR Скачать руководство пользователя страница 4

GERNERAL

 

INFORMATION

 

B

E SURE TO READ THE SAFETY INSTRUCTIONS CAREFULLY BEFORE OPERATING YOUR MODEL

 

• Always foll

ow the procedures and settings recommended in the instructions.  

• If you are using remote

-controlled model aircraft, helicopters, cars or ships for the first time, we recommend that you ask an 

experienced model pilot for help.  

• Remote

-controlled models are not toys in the usual sense and may only be used and operated by young people under 14 years of 

age under the supervision of adults.  

• Their construction and operation requires technical understanding, careful craftsmanship and safety

-conscious behaviour.  

• Mistakes or negligence during construction, flying or driving can result in considerable damage to property or personal inj

ury.  

• Since the manufacturer and seller have no influence on the proper construction/assembly and operation of the models, 

these risks 

are expressly pointed out and any liability is excluded.  

• Propellers on aircraft and all moving parts in general pose a constant risk of injury.

 Avoid touching such parts at all costs.  

• Note that motors and controllers can reach high temper

atures during operation. Avoid touching such parts at all costs.  

• Never stay in the danger area of rotating parts with electric motors with connected drive battery.

  

• Overcharging or incorrect charging can cause the batteries to explode.

 Make sure the polarity is correct.  

•  Protect  your  equipment  and  Models  from  dust,  dirt  and  moisture.

 Do  not  expose  the  equipment  to  excessive  heat,  cold  or 

vibration.  

• Always check your equipment for damage and replace defects with original spare parts.

  

• Do not use 

equipment that has been damaged or got wet due to a fall, even if it is dry again!  

• Do not make any changes to the remote control which are not described in these instructions.

  

•Before the first flight, check the wing symmetry, tail unit and fuselage.

 All parts of the model should have the same spacing from 

the left and right wing or tail plane to the centre of the fuselage or the same angle.  

 

 

A

TTENTION

,

 DANGER OF INJURY

 

• Always keep a safe distance from your model aircraft.

  

• Never fly over specta

tors, other pilots or yourself.  

• Always perform flight figures in a direction away from the pilot or spectators.

  

• Never endanger people or animals.

  

• Never fly near power lines or residential areas.

  

• Do not operate your model near locks or public sh

ipping.  

• Do not operate your model on public roads, motorways, paths and squares, etc., but only in approved locations.

  

• Do not operate the model in thunderstorms.

  

• Before each flight, check your remote control system for sufficient function and rang

e.  

• After flying, remove all batteries from the model.

  

Do not „aim“ the transmitter antenna at the model during operation.

 In this direction, the transmitter has the lowest radiation. The best position 

of the antenna is to the side of the model.  
Use of devices with image and/or sound recording function: 

 

 
 

Содержание MILES M.2H HAWK MAJOR



















Отзывы: