manualshive.com logo in svg

Value Hobby F3A Oasis, Инструкция по эксплуатации

Поделиться
Скачать
Value Hobby F3A Oasis Скачать руководство пользователя страница 31

                                                 http://www.valuehobby.com/ 

 31

Section 12: Setting CG and Control Throws 

Recommended CG   

For the first flights, the recommended Center of Gravity location is 

165mm

 behind the leading 

edge of the wing against the fuselage. Use the battery pack, moving it forward or backward, to 

achieve the correct balance. 

Control throws 

For the AILERONS we recommend the following throws:     

High rate:

 40° left & right     

Normal flight: 

D/R: 30% Expo: 20%     

Snap

: D/R

:

 100% Expo: 90%     

Spin & 3D:

 D/R: 100% Expo: 90%     

   

For the ELEVATOR we recommend the following throws:     

High rate:

 40° up & down     

Normal flight: 

D/R: 30% Expo: 30%     

Snap:

 D/R: 40% Expo: 50%     

Spin & 3D:

 D/R: 100% Expo: 95%     

   

For the RUDDER we recommend the following throws:     

High rate: 

40° left & right     

Normal flight: 

D/R: 40% Expo: 60%     

Snap: D/R:

 50% Expo: 70%     

Spin & 3D: 

D/R: 100% Expo: 90% 

Note: that Futaba and Hitec radios require NEGATIVE exponential, while JR and Spektrum 

use POSITIVE exponential. 

 

Range test your radio   

step1.

 

Before fly, be sure to range check your radio as manufacturer’s instruction 

manual of your radio-system recommand. 

step2.

 

Double-check all controls (aileron, elevator, rudder and throttle) move in the 

correct direction.   

step3.

 

Be sure that your LiPO battery is fully charged. 

 
 
 
 
 
 
 
 
 
 

Содержание F3A Oasis

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды