Valor Valor 7000 series Скачать руководство пользователя страница 30

Страница: 30 / 40

EN-28

Valor™ 7000

Series

6. MAINTENANCE

6.1 Cleaning

The housing may be cleaned with a cloth dampened with a mild detergent if necessary. Do not
use solvents, chemicals, alcohol, ammonia or abrasives to clean the housing or control panel.

6.2 Troubleshooting

Table 6-1 lists common problems and possible causes and remedies.
If the problem persists, contact OHAUS or your authorized dealer.

TABLE 6-1

Symptom

Possible Cause

Remedy

Cannot turn on

No power to scale

Verify connections and voltage

Poor accuracy

Improper calibration
Unstable environment

Perform calibration
Move scale to suitable location

Cannot calibrate

LFT locked

See chapter 5 for more information

Cannot access mode

Mode not enabled

Enter menu and enable mode

Cannot access unit

Unit not enabled

Enter menu and enable unit

Battery icon flashing

Low Battery error

Connect the scale to AC power and
charge the battery

Err 8.1

Power On Error

Weight reading exceeds Power On Zero
limit

Err 8.2

Power On Error

Weight reading below Power On Zero
limit

Err 8.3

Over Range Error

Weight reading exceeds Overload limit

Err 8.4

Under Range Error

Weight reading below Underload limit

Err 8.5

Tare out of range

Adjust tare value to be within range

Err 8.6

Display overflow

Weight exceeds 6 digits.

Err 9.5

Calibration data error

Calibration data not present

-------

Busy

Displayed during tare setting, zero
setting, printing

--NO--

Action not allowed

Function not executed

CAL E

Calibration error
Unstable environment
Incorrect calibration
weight

Calibration value outside allowed limits
Move the scale to suitable location
Use correct calibration weight

Lo.rEF

Low reference weight
warning

Increase reference weight

rEF.Err

Unacceptable reference
weight

Reference weight too small. Weight on
the pan is too small to define a valid
reference weight. Increase reference
weight

NO.ACC

Gross and net weights
cannot be accumulated
together

Only accumulate gross or net weights
(only works in LFT)

Battery fails to charge
fully

Battery is defective

Have battery replaced by Ohaus
authorized service dealer.

Содержание Valor 7000 series









































Результаты поиска

Содержание Valor 7000 series

Отзывы:

Бренды по названию

Популярные бренды

Valor Valor 7000 series, Инструкция по эксплуатации

Результаты поиска

Содержание Valor 7000 series

Отзывы:

Бренды по названию

Популярные бренды