background image

Warranty

1. Extended Warranty Coverage

For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the 

initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in material or 

workmanship under normal conditions of use and service:

2. Two-Year Parts Warranty 

In addition, for two (2) years from the date of purchase, the Company, at its option, can repair or exchange all parts and components 

not listed above but that are found to have a 

bona fide

 defect in material or workmanship under normal conditions of use.

3. Conditions and Limitations

The warranty registration card must be completed by the initial owner and returned to the Company within 90 days of purchase.

Installation and maintenance must be performed by an authorized and trained dealer in accordance with the Company’s installation 

instructions.

This warranty is void where installation of the unit does not conform to all applicable codes including national and local gas 

appliance installation codes and building and fire codes.

The owner must comply with all operating instructions.

The Company is not responsible for the labor costs to remove defective parts or re-install repaired or replacement parts.

The first purchaser or user of the unit will be responsible for any shipping charges for replacement parts as well as travel time 

incurred by the dealer to perform the warranty work.

This warranty applies to non-commercial use and service and is void if it is apparent that there is abuse, misuse, alteration, 

improper installation, accident or lack of maintenance to the unit.

This warranty does not cover damage to the unit through:

i) 

Improper installation, operational or environmental conditions.

ii)  Inadequate ventilation in the area or competition for air from other household equipment or appliances.

iii)  Damage due to chemicals, dampness, condensation, or sulphur in the fuel supply lines which exceeds industry standards.

This warranty does not cover glass, log breakage or damage to the unit while in transit.

The Company does not allow anyone to extend, alter or modify this warranty and assumes no responsibility for direct, indirect or 

consequential damages caused by the unit. State or provincial laws where the first purchaser or user resides may provide specific 

rights to extend this warranty and, if so, the Company’s sole obligation under this warranty is to provide labor and/or materials in 

accordance with those laws.

4. Discharge of Liability

After two (2) years from the date of purchase, the Company may, at its option, fully discharge all obligations under this warranty by 

paying to the first purchaser/user the wholesale price of any defective parts.

5. No Other Warranty

All obligations to repair this unit are defined in this warranty. Some states or provinces may specifically mandate additional warranties 

on the part of manufacturers, but in the absence of such specific legislation, there is no other warranty or obligation expressed or 

implied.

a)

b)

c)

d)

e)

f)

g)

h)

i)

j)

Part or Component

Defect Covered

Maximum Warranty Period

Exterior steel casing

Corrosion

10 years

Glass

Loss of structural integrity

10 years

Cast iron parts

Corrosion

10 years

Firebox and heat exchanger

Corrosion (but not discoloration) causing 

loss of structural integrity

10 years

WARR

ANT

Y P

ROG

RAM

WARR

ANT

Y P

ROG

RAM

VA

LOR

CO M FO

R

T

VA

LOR

CO M FO

R

T

VA

LOR

CO M FO

R

T

If you have a problem with this unit, please contact your dealer or 

supplier immediately. Under no circumstances should you attempt 

to  service  the  unit  in  any  way  by  yourself.  The  warranties  in 

paragraphs 1 and 2 are provided only to the first purchaser/user of 

this unit, are not transferable and are subject to the conditions and 

limitations in paragraphs 3, 4 and 5. Please review the conditions 

and limitations carefully and strictly follow their requirements.

Содержание Portrait 530ICN/ICP





































Отзывы: