background image

Supply Gas Installation

The gas supply inlet connection is a 1/2” NPT female. 

Gas shut-off valve supplied on the end of stainless 

steel flexible connector. Flex connector is located on 

the left hand rear corner of the appliance.

Use only new black iron or steel pipes or copper tubing 

if acceptable—check local codes. Note that in USA, 

copper tubing must be internally tinned for protection 

against sulfur compounds.
The burner module and gas train on this appliance 

may be removed as a unit for servicing. The flex pipe 

supplied with the unit provides a union for removal of 

the module.
Unions in gas lines should be of ground joint type.
The gas supply line must be sized and installed to 

provide a supply of gas sufficient to meet the maximum 

demand of the appliance without undue loss of 

pressure.
Sealant used must be resistant to the action of all 

gas constituents including LP gas. Sealant should be 

applied lightly to male threads to ensure excess sealant 

does not enter gas lines.
Pressure test the supply line for leaks.
The appliance and its individual shut-off valve must be 

disconnected from the gas supply piping system during 

any pressure testing of that system at test pressures in 

excess of 1/2 psig (3.5 kPa).
The appliance must be isolated from the gas supply 

piping system by closing its equipment shut-off valve 

during any pressure testing of the gas supply piping 

system at test pressures equal to or less than 1/2 psi 

(3.5 kPa).
Failure to either disconnect or isolate the appliance 

during pressure testing may resulting regulator or 

valve damages and void the warranty. Consult your 

dealer in case of damages.

X

X

Pressure Testing

Manifold Test 

Pressure

Valve Inlet 

Pressure

Valve Assembly

Control 

Valve

34” (864 mm) 

flex pipe 

supplied with 

appliance

Shut-off valve 

supplied with 

appliance

1/2” NPT 

female

Manifold 

Pressure 

Adjustment 

behind 

Plastic Cap

Pressure Test Points

The minimum supply pressure is given in the 

subsection 

Ratings

 of this manual—page 5.

All piping and connections must be tested for leaks 

after installation or servicing. All leaks must be 

corrected immediately.
When testing for leaks:
•  Make sure that the appliance is turned off.

•  Open the manual shut-off valve.

•  Test for leaks by applying a liquid detergent or soap 

solution to all joints. Bubbles forming indicate a gas 

leak. 

Never use an open flame to check for leaks. 

Correct any leak detected immediately.

The pressure test 

tapping locations is 

shown in the figure 

below. An internal 

regulator within the 

valve controls the 

burner manifold 

pressure. 
The correct pressure 

range is shown in the 

table in subsection 

Ratings

 of this manual 

on page 5. The 

pressure check should 

be made with the 

burner alight and at its 

highest setting. See 

Lighting Instructions

 

section for full operating 

details on page 33.

14

Содержание LEGEND G4 780IN (NG)











































Отзывы: