background image

3

Flame Height

The flame height can be adjusted in the following manners. 

1.  Press the     (large flame) button to turn on the main burner.

2.  Press the     (large flame) button to increase the flame height.

3.  Press the     (small flame) button to decrease the flame height or to go to pilot position.

For fine adjustments, tap the     

 

and

    

 buttons.

NOTE: While pressing either button, a symbol indicating transmission appears on the upper right 
hand corner of the display. The receiver confirms transmission with an acoustic signal.

hours

minutes

Time

To set the time, follow the steps below. 

1.  The display indicates °C/24-hour or °F/12-hour clock. To change from one to the other, press 

and hold both the 

OFF

 and     buttons until the display changes.

2.  To set the time, hold down 

both

 the     and     buttons until the display fl ashes. Let go.

3.  Quickly press the     button to set the hour and the     button to set the minutes. 

Note: You must start setting the time while the display is fl ashing. If it stops fl ashing, go back to 2. 

4. Press 

the 

OFF

 button.

Handset / Receiver Match

The remote control handset and receiver are programmed to function together. In case of a replacement of the handset 
or the receiver, you will need to reset the receiver to allow them to function together. Contact your dealer for details

Low Battery Indication

Remote handset:

 

BATT

 will appear on the display when 

the battery needs to be replaced.
Replace with one 9 V 

alkaline 

battery.

Receiver:

 Three short ‘beeps’ will sound when the motor 

turns when the batteries need to be replaced. Replace with four 1.5 V 

alkaline 

batteries.

NOTE: 

With very low battery, the valve shuts off the fi re completely. This does not happen when the power supply is 

interrupted.

CAUTION

DO NOT USE

 a screwdriver or other metallic object 

to remove the batteries from the battery box or the 
handset! This could cause a short circuit.

Designed and Manufactured by / for

Miles Industries Ltd.

 190–2255 Dollarton Highway, North Vancouver, BC, CANADA  V7H 3B1

Tel. 604-984-3496  Fax 604-984-0246

www.valorfi replaces.com

Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.

Содержание GV60NTK







Отзывы: