Basic fan speed
=
1
Maximum fan speed
=
8
Carbon dioxide adjustment (CO
2
)
=
900 ppm CO
2
Basic humidity level
=
automatic or manually chosen value
Adjustment interval
=
10 min
Freezing protection (cell)
=
3˚C
Freezing protection hysteresis
=
3˚C
Preheating setting
=
-3˚C (change to +5˚C if you want to use preheating)
Maintenance reminder
=
4 months
Cell bypass
=
12˚C
Cascade control
=
not used
Humidity level (RH level) adjustment =
automatic
Switch type
=
fireplace switch
3.5. Factory settings
VALLOX 90 SE
11
INSTRUCTIONS FOR USING THE CONTROL PANEL
3.4. Week clock control
The week programme can be used to set the desired fan speed (basic fan speed) and supply air
temperature for each hour of the day on seven days a week. The week programme overrides
manual adjustments.
Carbon dioxide and humidity adjustment can increase fan speed but never decrease it below the
basic fan speed set in the week programme.
3.4.1.
Week programme programming
D
Hr
Sp
Tmp
1
12
5
20
Exit
Cursor
D
Day 1…7
1 = Monday, 2 = Tuesday, etc.
Hr Hours, 0…23
Sp Fan speed, 1…8
Tmp Supply air temperature, 10...30 ºC
Exit Save the setting and exit
N
No change to previous
Example: Monday
Fan speed is increased to speed 2 and supply air temperature to 17 ºC between 07:00 (7 a.m.)
and 17:00 (5 p.m.) hours. After that, fan speed is raised to speed 4 and supply air temperature to
20 ºC. For the evening, fan speed is boosted to speed 6 between 19:00 and 21:00 hours (for the
period when a sauna bath is taken), after which fan speed is lowered back to 4.
Move the cursor with the arrow keys and change values with the + and – buttons. Note that Exit
and saving are done when the programming is finished by moving the cursor below the word Exit
and pr or –.
Changes in fan speed (Sp) and supply air temperature (Tmp) are only made for the hours desired;
in other cases, use N (no change to previous).
Monday (D = 1), 07:00 hours (H = 7), fan speed 2 (Sp = 2), supply air temperature 17 ºC (Tmp =
17). Move the cursor to the following hour.
Monday (D = 1), 16:00 hours (H = 16), fan speed 4 (Sp = 4), supply air temperature 20 ºC (Tmp
= 20). Move the cursor to the following hour.
Monday (D = 1), 19:00 hours (H = 19), fan speed 6 (Sp = 6), supply air temperature unchanged
(Tmp = N). Move the cursor to the following hour.
Monday (D = 1), 21:00 hours (H = 21), fan speed 4 (Sp = 4), supply air temperature unchanged
(Tmp = N). Move the cursor to the following day.
Similar changes have to be made separately for each day. Finally, exit the programming mode by
selecting Exit. If you wish, you can erase the week programme as indicated in section 3.3.3. You
can then start programming from the start. You can see the settings programmed by choosing a day
and by scrolling the hours with the + or – button.
D
Hr
Sp
Tmp
1
7
2
17
Exit
D
Hr
Sp
Tmp
1
16
4
20
Exit
D
Hr
Sp
Tmp
1
19
6
N
Exit
D
Hr
Sp
Tmp
1
21
4
N
Exit
Move the cursor with the arrow keys and change values with the + and – buttons. Exit
and saving are done when the programming is finished.
Monday (D = 1), hours 15 (H = 15), minutes (M = 30).
Time is maintained even though there is a power failure.
3.4.2. Adjusting
time
day hour
min
1
15
30
Exit
day Day 1…7
1 = Monday, 2 = Tuesday, etc.
hour Hours, 0…23.
min Minutes 0…60
Exit Save the setting and exit
Cursor
Содержание 90 SE Series
Страница 17: ......
