Valco baby Spark, Руководство по продукции

Страница: 7 / 8

• Place the lining over the bassinet interior and
align the openings in the lining with the bassinet
housing and hood connection sites (c).
• Secure the lining over the bassinet sides to the
Velcro tabs located on the bassinet outer body.
• Reinstall the hood and bumper bar.
• Attach the bootcover/apron to the open foot
of the bassinet, locating and securing to the
snaps at the side of the bassinet body.
To convert your bassinet to a stroller seat.
• Reverse the process out lined previously
• Remove the apron and lining
• Zip up the footwell
• Buckle all support straps beneath the seat
• Install the hood and bumper bar
IMPORTANT MATTRESS WARNING
Unlike cribs that have rigid sides, the bassinet
mattress is specially designed to prevent
suffocation. The mattress is designed to be
a snug fit and should not exceed 30mm in
thickness. Using a thicker or different sized
mattress may allow a child’s head to Get
between the mattress and the side of the
bassinet causing suffocation. To help prevent
suffocation from entrapment, USE ONLY THE
MATTRESS PROVIDED.
NEVER use additional mattress or padding.
Use only the fitted sheet provided.
WARNING: DO NOT USE THIS BASSINET
ONCE THE CHILD CAN SIT UP UNAIDED
9>BUMPER BAR
Insert each side of the bumper bar fitting into
the corresponding housing (a) in the seat
frame until you hear it click into place.
The bumper bar can be opened as a “gate” for
easy access pressing on one of the release
buttons (b) and lifting the side out of the
housing. For full removal, repeat this process
for the other side.
10>HOOD
Locate the hood stud fixtures found on either
side of the stroller, and align hood clamp to
studs. Attach clamp onto frame (a).
Your SPARK hood is designed to provide
maximum shade and comfort for your child by
incorporating our EXPANDA HOOD section.
To increase/decrease the hood size
Open the EXPANDA HOOD section fully
using the zip. Gently pull your hood forward;
extending it as far as is required.
When no longer needed, fold the EXPANDA
HOOD backward, allowing it to fold in on itself.
Gently zip the section closed being mindful not
to catch any of the fabric in the zipper teeth.
11>HARNESS
Your stroller harness is specifically designed
with many built in safety features.
This includes the requirement that, when
opened, all straps are released so that no
dangerous loops can be formed causing a
strangulation hazard.
WARNING: USE THIS HARNESS AT ALL TIMES.
Closing your harness: Slide each of the
shoulder strap bottom guides (a) into the
corresponding channel (b) on the top of each
side strap prong. Insert each completed prong
into the central buckle housing (c).
Carefully adjust the harness straps to snugly fit
your child by adjusting the sliders (d) located
on each strap. The harness should be fitted to
your child’s body, tight enough so that they
cannot wriggle free of the straps but, loose
enough, so as not to cause any discomfort.
For even more flexibility, the height at which
your shoulder straps are fitted to the stroller
can be adjusted at 3 pointse).
To change the shoulder strap position:
From the rear of the seat, thread the top of
the strap back through the harness slot (it fits
through the slot.
Rethread the strap back through the desired
slot from the front of the seat
Opening your harness: Press the central
housing button (e). This will release both side
prongs from the central housing. The shoulder
and waist straps will release automatically from
each other.
If the shoulder and waist straps do not
automatically disengage from each other,
manually slide the guides of the waist channels.
Your harness will separate into 5 sections.
IMPORTANT WARNING: WHEN NOT IN USE, BE
SURE THE SHOULDER AND WAIST STRAPS ARE
ALWAYS DISCONNECTED FROM THE CENTRAL
HOUSING AND EACH OTHER.
12>BRAKES
Press down on the long leg of the brake lever
(a) located on the rear axle to simultaneously
engage the brake in both rear wheels.
To release, press down on the shorter leg with
your foot.
IMPORTANT WARNING: ALWAYS TEST
THAT THE BRAKES ARE SECURELY
DISENGAGED BEFORE US
E.
13>BOOTCOVER
Attach the bootcover/apron to the open foot of
the bassinet or seat, locating and securing to
the snaps at the side of the bassinet body.
14>FOLDING
Your Spark can be folded with the seat in facing in
either direction as well as in bassinet mode.
• Release the handle by simultaneously lifting
the triggers (a).
• Swing the handle over the seat/bassinet
body. As it passes the central pivot joint (b) the
lower frame will automatically release and the
stroller will fold down completely.
• The chassis will lock in the closed position
automatically.