Vaisala MGP261 Скачать руководство пользователя страница 38

Страница: 38 / 90

4.2.1 Installing the Driver for the USB Service Cable

Only Windows

operating systems are supported by the driver of the USB

service cable.

1. Connect the USB service cable to a USB port on your computer. Windows

detects the

new device and installs the appropriate driver.

2. Open

Devices and Printers

from the Windows

Start menu. Use search to find it if

necessary (search for "devices").

3. Locate the cable in the list of devices:

• If the device is listed as

Vaisala USB Device

with a COM port number in brackets, the

cable is ready for use. Take note of the COM port number for later use.

• If the device is listed as

Vaisala USB Instrument Cable

without a COM port number

listed, you must install the driver manually.

4. To install the driver manually:

a. Disconnect the USB service cable from the computer.

b. Download the Vaisala USB driver at

www.vaisala.com/software

(search and select the

appropriate USB Instrument Driver Setup for your cable).

c. Run the USB driver installation program

Vaisala USB Device Driver

Setup.exe

. Accept the installation defaults.

d. Go back to

step 1

and verify that the driver installation works as expected.

MGP261 User Guide

M212273EN-A

Содержание MGP261



























































































Результаты поиска

Содержание MGP261

Отзывы:

Бренды по названию

Популярные бренды

Vaisala MGP261, Руководство пользователя

Результаты поиска

Содержание MGP261

Отзывы:

Бренды по названию

Популярные бренды