manualshive.com logo in svg

Vaisala HUMICAP HMM105, Техническое описание, Страница: 20 / 23

Поделиться
Скачать
Vaisala HUMICAP HMM105 Скачать руководство пользователя страница 20

Technical Reference _________________________________________________________________  

18 ________________________________________________________________ M211638EN-C 

Table 30 

Adjustment Return Codes 

Code  Meaning 

0 

Ok 

1 

Function not supported 

2 

Sequence error 

3 

Recorded-Reference difference too large 

4 

2-point adjustment: Points too close  

Adjusting Measurement 

HMM105 can be adjusted while it remains installed in an incubator. 

Create the reference environment inside the chamber, and use the 

Adjust

 

command to perform the adjustment sequence. 

Adjustment can fail for a number of reasons. Refer to the list of return 

codes for the Adjust command in Table 30 above. 

One Point Adjustment 

To perform a one point adjustment of relative humidity (RH) or 

temperature (T), you must perform the following sequence: 

1. 

Using the 

Adjust

 command,  start 1 point adjustment for the 

chosen parameter.  

2. 

Place the sensor in the reference environment and wait until the 

measurement has stabilized. 

3. 

Using the 

Adjust

 command, record the measured point and give 

the reference value. 

 4.  Use the 

Adjust

 command to end the adjustment. 

Two Point Adjustment 

To perform a two point adjustment of relative humidity (RH) or 

temperature (T), you must perform the following sequence: 

1. 

Using the 

Adjust

 command,  start 2 point adjustment.  

2. 

Place the sensor in the low end reference and wait until the 

measurement has stabilized. 

3. 

Using the 

Adjust

 command, record the first measured point and 

give the first reference value. 

4. 

Place the sensor in the high end reference and wait until the 

measurement has stabilized. 

5. 

Using the 

Adjust

 command, record the second measured point and 

give the second reference value. 

6. 

Use the 

Adjust

 command to end the adjustment. 

Содержание HUMICAP HMM105
























Отзывы:

Нет отзывов