Vaillant VRT 340f Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

Vaillant VRT 340f Скачать руководство пользователя страница 15

15

GB

Operating manual

VRT 340f

Display

Required steps

Press the dial. The cursor
marks the start time and the
hour display flashes.
Select the start time by
turning the dial. Press
the dial again to set the
minutes.

Press the dial. The cursor
marks the end time and the
hour display flashes.
Select the end time by
turning the dial. Press
the dial again to set the
minutes.

Table 4.3 Setting time windows

If necessary, you can switch the room
temperature thermostat from the week
programme to a daily programme.
• With the display in normal mode, press

the F button for about 10 seconds.
When you programme time windows,
days of the week will no longer be
displayed.

4.4

Setting the room temperature

The current room temperature is shown
in the basic display.
You can set the room temperature
directly from the basic display.
You can also set or change the set-back
temperature "ECO“ in the basic display.

Operation 4

«
...
13
14
15
16
17
...
»

Содержание VRT 340f









































Отзывы:

Нет отзывов