Index
29
Reading the software version................................................ 8
Reading the status ............................................................ 11
Circulation pump............................................................ 14
Cylinder charging pump................................................. 14
Heating circuit mixer ...................................................... 13
Heating pump ................................................................ 13
Solar pump .................................................................... 16
Reading the status for the external heat demand ............... 13
Reading the status of the heating circuit ............................. 11
Reading the status, temperature difference control ............ 18
Reading the system status .................................................... 7
Reading the top cylinder temperature for heating ............... 16
Reading the top cylinder temperature for hot water ............ 16
Reading the top cylinder temperature for the buffer
cylinder ................................................................................ 16
Reading the value, bottom cylinder temperature sensor..... 17
Reading the value, solar yield sensor ................................. 16
Reading the value, system flow temperature ...................... 10
Reading the value, temperature difference sensor 1 .......... 18
Reading the value, temperature difference sensor 2 .......... 18
Reading the water pressure .................................................. 7
Reading the zone valve status ............................................ 14
Reading, zone valve status ................................................. 14
Regulations ........................................................................... 3
Removing the controller, heat generator ............................. 19
Removing the controller, living room ................................... 19
Resetting the running time, solar pump............................... 16
S
Second temperature difference control, defining the switch-
off differential....................................................................... 17
Second temperature difference control, defining the switch-
on differential....................................................................... 17
Selecting the auxiliary heater support ................................... 9
Selecting the expansion module for the actuator test ......... 18
Selecting the expansion module, actuator test.................... 18
Selecting the expansion module, sensor test...................... 18
Sensor test, selecting the expansion module...................... 18
Setting
End OT cooling
...................................................... 13
Setting
Start OT cooling
...................................................... 8
Setting the alternative point................................................... 9
Setting the anti-cycling time, hot water demand.................. 15
Setting the collector temperature ........................................ 17
Setting the cooling start temperature .................................... 8
Setting the cooling stop temperature................................... 13
Setting the cylinder.............................................................. 14
Setting the cylinder target temperature, domestic hot water
cylinder ................................................................................ 14
Setting the day target flow temperature .............................. 11
Setting the day temperature ................................................ 14
Setting the excess temperature........................................... 12
Setting the flow rate, solar circuit ........................................ 16
Setting the frost protection delay........................................... 8
Setting the heating bivalence point ....................................... 9
Setting the heating curve..................................................... 12
Setting the hot water bivalence point .................................... 9
Setting the hot water target flow temperature ..................... 16
Setting the hysteresis, cylinder charging............................. 15
Setting the limp home mode temperature ............................. 9
Setting the maximum charging time, cylinder...................... 15
Setting the maximum target flow temperature..................... 12
Setting the maximum temperature ...................................... 18
Setting the minimum target flow temperature...................... 12
Setting the minimum temperature ....................................... 18
Setting the offset for charging the buffer cylinder for the
heating circuit ...................................................................... 10
Setting the offset, dew point ................................................ 13
Setting the OT constant heating............................................ 8
Setting the output, auxiliary heater...................................... 10
Setting the purging time ...................................................... 17
Setting the set-back target flow temperature....................... 11
Setting the set-back temperature ........................................ 14
Setting the solar circuit protection ....................................... 17
Setting the switch-off threshold ........................................... 12
Setting the target flow temperature, cooling........................ 11
Setting the target flow temperature, maximum.................... 12
Setting the target flow temperature, minimum..................... 12
Setting the target return temperature .................................. 11
Setting the temperature, day ............................................... 14
Setting the temperature, set-back ....................................... 14
Setting the type of circuit ..................................................... 11
Solar charging, defining the switch-off differential............... 17
Solar charging, defining the switch-on differential............... 17
Solar circuit, setting the flow rate ........................................ 16
Solar pump, reading the running time ................................. 16
Solar pump, reading the status ........................................... 16
Solar pump, resetting the running time ............................... 16
Solar yield sensor, reading the value .................................. 16
Specifying the controller behaviour ..................................... 12
Starting up ............................................................................. 7
System flow temperature, reading the value ....................... 10
T
Temperature difference control, reading the status ............ 18
Temperature difference sensor 1, reading the value .......... 18
Temperature difference sensor 2, reading the value .......... 18
Z
Zone activated..................................................................... 14
Zone assignment................................................................. 14
0020200781_01
VR
C
700/2
Installation instructions
