background image

6

Operating instructions for VED electric instantaneous water heater 0020149586_00

4 Energy-saving 

tips

You can help to save energy by following the tips and 
advice below:

Appropriate hot water temperature

The water should only be heated up to the extent that is 
necessary for use. Any further heating will result in 
unnecessary energy consumption. For you, this means 
that you should:

 

>

Set your VED to stage I in normal operating mode.

 

>

Briefly set the output selector to stage II in special 
cases where you need more hot water than stage I is 
able to provide. After using the hot water, remember 
to set the output selector back to stage I.

Detecting and rectifying faults

e

 

Danger!
Risk of death from electric shock.

Live lines and connections may cause a 
potentially lethal electric shock.

 

>

Do not attempt to repair the unit yourself 
under any circumstances.

 

>

Under no circumstances should the unit 
cladding be removed.

 

>

If the unit ever malfunctions, inform an 
approved heating specialist company 
immediately.

6 Care

There is no need to care for your Vaillant VED electric 
instantaneous water heater because all internal parts 
are protected against dirt and moisture. You can clean 
the exterior of the unit with a damp cloth and a little 
soap.

i

  Do not use any abrasive scouring or cleaning 

agents when cleaning the unit cladding.

Maintenance, guarantee and 
customer service

The permanent operational readiness, safety, reliability 
and long service life of your electronic VED electric 
instantaneous water heater require annual inspections 
and maintenance work to be carried out by a competent 
person.  

a

 Danger!

Risk of injury and material damage due 
to incorrect maintenance and repairs.

If you fail to carry out maintenance, or if 
you carry this out incorrectly, this may 
adversely affect the operating reliability of 
the unit.

 

>

Never attempt to perform maintenance 
or repairs on your 

VED

 

electric instanta-

neous water heater

 by yourself. 

 

>

You must employ an approved heating spe-
cialist company to complete such work. We 
recommend making a maintenance agree-
ment.

b

 Caution.

Possible material damage to the unit.

A lack of maintenance can affect the func-
tional safety of the VED. E.g. unit defects 
caused by limescale formation. In areas of 
hard water (more than 14 °dH = 2.5 
CaCO

3

 mmol/l) or very hard water (more than 

20 °dH = 3.6 CaCO

3

 mmol/l), a significantly 

more frequent maintenance interval may be 
required.

 

>

Have your VED inspected at least every 
3 years by a competent person.

 

>

If you live in an area with very hard water, 
Vaillant recommends that you have the 
maintenance service carried out once a 
year by a competent person.

Recycling and disposal

 

 If your Vaillant unit is labelled with this symbol, it 
does not belong with your household waste at the 
end of its useful life. 

 

>

Instead, take the unit to a collection point for recycling 
electrical and electronic devices.

For more information on where to take your used electrical 
or electronic devices, contact your town or district authori-
ties, waste disposal company, or the competent person who 
installed the unit.

4 Energy-saving tips, 5 Detecting and rectifying faults, 6 Care 
7 Maintenance, guarantee and customer service 8 Recycling and disposal

Содержание VED





























Отзывы: