manualshive.com logo in svg

Vaillant ecoTEC SERIES, Инструкция по установке и обслуживанию

Поделиться
Скачать
Vaillant ecoTEC SERIES Скачать руководство пользователя страница 51

51

Instructions for installation and servicing ecoTEC 839592_12

 

Display Meaning

Display value/adjustable value

d.36

Hot water flow sensor

in l/min

d.40

Flow temperature

Actual value in °C

d.41

Return temperature

Actual value in °C

d.44

Digitised ionisation potential

Display range of 0 to 102, > 80 no flame, < 40 even flame

d.47

Outside temperature 
(with weather compensating Vaillant controller only)

Actual value in °C

d.67

Remaining burner anti cycling time

in min

d.76

Appliance variant (device specific number)

00 to 99

d.90

Digital regulator status

1 = identified, 0 = unidentified (eBUS Address <=10)

d.91

DCF status with connected external probe with DCF77 
receiver

0 = no reception, 1 = reception, 2 = synchronised, 3 = valid

d.97

Activation of the second diagnostic level

Password: 17

Table 8.2  Diagnostic codes of the first diagnostic level 

(continued)

Second diagnostic level

•  As described above in the first diagnostic level, scroll 

through the diagnostic number 

d.97

.

•  Change the displayed value to 

17

 (password) and 

press the “

i

” button.

You are now in the second diagnostic level where all 
information from the first diagnostic level (see Table 
8.2) and the second diagnostic level (see Table 8.3) is 
displayed.

Display Meaning

Display value/adjustable value

d.17

Heating flow/return regulation changeover

0 = flow, 1 = return (factory setting: 0)

d.18

Pump mode (return)

0 = return, 1 = nonstop, 2 = winter (factory setting: 0)

d.19

Only in ecoTEC plus:
Operating modes of the two-speed heating pump

0 =  pre ignition speed 1, hot water or heating speed 2, overrun speed 

1

1 =  pre ignition speed 1, hot water speed 2, heating speed 1, overrun 

speed 1

2 =  like 1, but speed in heating mode dependent on heating part 

load d. 0 (if d.0 is below 60% of full load, then pump speed 1, 
otherwise speed 2)

3 =  always speed 2
(factory setting: 2)

d.20

Maximum set value for target cylinder temperature 
(system boilers only)

Setting range: 50 to 70 °C (factory setting: 65 °C)

d.27

Switching accessory relay 1 in the accessory module

1 = Circulation pump (default)
2 = Ext. pump
3 = Storage charging pump
4 = Flue gas flap/extractor hood
5 = External gas valve
6 = External error message

d.28

Switching accessory relay 2 in the accessory module

1 = Circulation pump
2 = Ext. pump (default)
3 = Storage charging pump
4 = Flue gas flap/extractor hood
5 = External gas valve
6 = External error message

Table 8.3 Diagnostics codes of the second diagnostic level

Scrolling and changing values and exiting the diagnostic 
mode is done as described in the first diagnostic level.

 Note

After exiting the second diagnostic level, if you 
press “i” and “+” within 4 minutes, you will 
directly reach the second diagnostic level 
without having to enter the password again.

Troubleshooting 8

Содержание ecoTEC SERIES

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды