background image

6

Installation - Quick guide

 7

 8

 9

1

2

3

5

1

2

3

5

4

7

Installation

Prepare the wall with 2 copper pipes 

at 147-153mm centres. Make sure the 

pipes are level 

(Fig. 1)

Connect the water supply to the 

inlet pipes. The hot water should be 

connected to the left hand pipe .
Before installing your new mixer, 

flush through the pipe work to ensure 

removal of debris, turn off the water 

supply. (Do not allow dirt, metal 

particles or shavings to block the filters 
fitted on inlets).

Temporarily place the valve over the 

copper pipes and mark the back of the 

body against the wall. 
There is a small amount of adjustment  

on the inlet pipes to allow fitting onto 

the copper pipes. Screw each side 

in or out as required, ensuring that 

both sides are screwed in equally & 

within the tolerance specified on the 

dimension page. 

Remove the valve 

(Fig. 2)

.

Remove the mounting plate from the 

back of the valve by releasing the two 

grub screws and pulling out the plate.
Place the mounting plate in the centre 

of the marked position and mark the 

two fixing holes.
Drill the marked holes to a suitable 

depth for the wall plugs and secure 

with supplied screws 

(Fig. 3)

.

If you are fitting the valve to a partition 

wall or a wall of particularly soft 

substrate you will need specialist fixings.

147-153mm

Mounting plate

Wall plugs

Screws

Fig. 1

Fig. 2

Fig. 3

Inlet pipe

20-25mm hole

Содержание WG-179M-CP







Отзывы: