Vacon OPTA1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 23

background image

12 • vacon

Description of parameters

Tel.+358 (0)201 2121 • Fax +358 (0)201 212 205

4.

DESCRIPTION OF PARAMETERS

4.1 Basic

parameters

2.1.1

Brake Chopper Level (ID1267)

Brake chopper operation level in volts. This is the DC link voltage level when the BCU
starts to discharge the capacitors through the brake resistor.

2.1.2

ID Run (ID631)

This parameter is used for manual identification for brake resistor connection. Brake
chopper unit makes automatic identification during every power-up. However, if resistor
connection is changed during service, ID Run can be executed manually with this
parameter by setting the value “1=ID Run”.

«
...
10
11
12
13
14
...
»

Содержание OPTA1
























Отзывы:

Нет отзывов

Похожие инструкции для OPTA1

Бренд: DAV TECH Страницы: 10

Бренд: Ebyte Страницы: 35

Бренд: K&K Страницы: 6

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 400

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 466

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

Бренд: Abov Страницы: 138

Бренд: Fluidmaster Страницы: 2

Бренд: KEY Страницы: 16

Бренд: Ezodo Страницы: 7

Бренд: Sensitron Страницы: 32

Бренд: Eaton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды