Vacon CXS Series Скачать руководство пользователя | Manualshive

Страница: 21 / 23

background image

VACON CX

Modbus user’s manual

Page

21

________________________________________________________________________________________

________________________________________________________________________________________
Vacon Oy

Phone +358-201-2121

Fax: +358-201-212 205

7.5

Installation of CX211OPT in Vacon CXS drives

NOTE: The option boards on the pictures may not look exactly the same as the one you have purchased.
These instructions are, still, applicable.

A

Remove the control panel and the panel base.

B

Remove the fixing screw from the control
board and replace it with a stand sleeve (4).

C

Connect the power cable (5) to terminal X5 of
the control board. The power cable can also
be connected to terminal X6 if terminal X5 is
already reserved by the power cable from the
power board.

D

Remove the protective foil of the plastic board
and place the plastic board above the control
board. Be sure to place the plastic board
correctly so that the stand sleeve (4) comes
out through the hole on the board.

E

Place the board on the protective plastic
board (6) and connect the data cable (2) to
terminal X14 of the control board. The stand
sleeve should come out through the metal-
edged hole.

F

Secure the board on the stand sleeve with
the screw (3) attached.

4

5

6

4

X14

2

3

«
...
19
20
21
22
23
»

Содержание CXS Series
























Отзывы:

Нет отзывов

Похожие инструкции для CXS Series

Бренд: Samsung Страницы: 22

Бренд: Accutrol Страницы: 25

Бренд: Teac Страницы: 2

Бренд: Ewellix Страницы: 18

Бренд: urmet domus Страницы: 7

KegMaster 4 Series

Бренд: Keg King Страницы: 17

sundi GLASSO GNT-248

Бренд: Zamel Страницы: 6

Бренд: Elvox Страницы: 36

Бренд: Globe Страницы: 4

Бренд: fadini Страницы: 12

Бренд: XtendLan Страницы: 14

Бренд: Videx Страницы: 8

VOCAL SOUND SYSTEM WITH REVERB PA 100

Бренд: Fender Страницы: 8

Dimensions D3200

Бренд: Leviton Страницы: 43

Бренд: Kelvinator Страницы: 16

Бренд: JLG Страницы: 48

Бренд: FOUR Страницы: 28

Бренд: Kraken Acoustics Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды