background image

 

 vacon 50x parameters

 vacon 

 

76

                                  24-hour s358 (0)40 837 1150 • Email: [email protected]

  

7

NOTE: Current limit is only available when Parameter 501 is set to Linear Auto. If Param-
eter 501 is set to Vector, then the Current Limiting values will actually be Torque Limiting 
values.

This parameter allows the function to disable either (a) undervoltage ride-through or (b) 
continuous Line Voltage Tracking (LVT) that produces dynamic Undervoltage Ride-Thru 
Thresholds. The following data values may be assigned to this parameter:

Parameter Value

Description

Disabled

This turns off the Undervoltage Ride-Thru function.

w/ LVT

This enables the standard Ride-Thru algorithm in the V/Hz 
modes and allows the choice of algorithm in the Linear Auto 
and Vector modes.

w/o LVT

This option operates in the same way as “w/ LVT” except that 
the Line Voltage Tracker function of the Undervoltage Ride-
Thru is not active. The Line Voltage will be estimated on pow-
ering up the drive.

No UV Fault

This mode is the same as “/o LVT” except if the bus recover 
from the ride-thru timeout state the under voltage fault is not 
generated. The bus voltage system will reset and goes back 
thru the startup sequence.

The Vacon 50X drive provides a Current Limit feature. With this feature enabled, the 
drive’s frequency is automatically reduced when operating in motoring mode to keep the 
measured torque within limits. When operating in regenerative mode, the output fre-
quency can be automatically increased for the same reason. In addition to the current 
limit parameters that activate the Current Limit mode, more current limit parameters 
are available to adjust the drive’s response to the load demands. The following data val-
ues may be assigned to this parameter:
The following data values may be assigned to this parameter:

Parameter Value

Description

Fixed Lvls

The fixed levels set in parameters 601, 602, 603 and 604 de-
termine the current limit in each of the four quadrants of op-
eration.

Vin2

Vin2 analog input sets the current limit value, range 0–200%

Cin

Cin analog input sets the current limit value, range 0–200%

Vin2 Motor

Vin2 analog input sets the motoring current limit value, range 
0–200%

Cin Motor

Cin analog input sets the motoring current limit value, range 
0–200%

Vin2 F-Mtr

Vin2 analog input sets the FWD motoring current limit value, 
range 0–200%

526 UV Ride-Thru En

Default = w/ LVT

Range: Text string
Level 2

Summary of UV Ride-Thru Enable Parameter (Parameter 
526)

Parameter Setting

Tracking

Ride-thru 
mode

UV Fault

Disabled

Disabled

Disabled

Disabled

w/ LVT

Enabled

Enabled

Enabled

w/o LVT

Disabled

Enabled

Enabled

No UV Fault

Disabled

Enabled

Disabled

600 Current Lim Sel

Default: Fixed Lvls

Range: Text string
Level 2

Содержание 50X





































































































































Отзывы: