Vacon 50X Скачать руководство пользователя | Manualshive

Страница: 69 / 132

background image

vacon 50x parameters

vacon

68

24-hour s358 (0)40 837 1150 • Email: [email protected]

7

This parameter configures the default length of time to accelerate from 0 Hz to the value
of parameter 302 (Max Frequency). This acceleration ramp is selected by parameter 401
(Ramp Select).
Note that extremely short acceleration times may result in nuisance fault trips.

This parameter configures the default length of time to decelerate from the value of pa-
rameter 302 (Max Frequency) to 0 Hz. The deceleration ramp is selected by Parameter
401 (Ramp Select).
Note that extremely short deceleration times may result in nuisance fault trips or may
require an external dynamic brake or regen current limit.

This parameter provides an alternate ramping time for the drive when accelerating, con-
figuring the length of time to accelerate from 0 Hz to the value of parameter 302 (Max
Frequency). This acceleration ramp is selected by parameter 401 (Ramp Select) or Se-
quencer Configuration.
Note that extremely short acceleration times may result in nuisance fault trips.

ART-F/R

Ramp-to-Stop

Running forward: 402 (Accel Time 1) and
403 (Decel Time 1).

Running reverse: 404 (Accel Time 2) and
405 (Decel Time 2)

ART-Frq

Ramp-to-Stop

If the output frequency is less than preset
frequency parameter 308 (Preset Freq 6),
the active ramp is set by 402 Accel Time 1
and 403 Decel Time 1. If the output fre-
quency is equal to or greater than 308
(Preset Freq 6), the active ramp is set by
404 (Accel Time 2) and 405 (Decel Time 2).

ART-Strt/RS

Ramp-to-Stop

This setting uses the Alternate Ramp for
Acceleration (parameter 404) to the set
speed, then uses the Main ramps (param-
eters 402 and 403) when the speeds are
adjusted. The drive will revert to the Alter-
nate Decel ramp (parameter 405) when a
Stop command is given.

S-Curve

Ramp-to-Stop

The drive uses 402 (Accel Time 1) and 403
(Decel Time 1) for total time and 414 as the
S Ramp Rounding value. The amount of
rounding is the same for that start and
stop of the ramp time.

ART-DI CTS

Coast-to-Stop

Same as ART-DI but with Coast-to-Stop

ART-F/R CTS

Coast-to-Stop

Same as ART-F/R but with Coast-to-Stop

ART-Frq CTS

Coast-to-Stop

Same as ART-Frq but with Coast-to-Stop

ART-Str/CS

Coast-to-Stop

Same as ART-Strt but with Coast-to-Stop

ART-STR/CTS

Coast-to-Stop

Same as S-Curve but with Coast-to-Stop

402 Accel Time 1

Default: 5.0 s

Range: 0.1–3200.0 s
Levels 1, 2

403 Decel Time 1

Default: 5.0 s

Range: 0.1–3200.0 s
Levels 1, 2

404 Accel Time 2

Default: 3.0 s

Range: 0.1–3200.0 s
Level 2

«
...
67
68
69
70
71
...
»

Содержание 50X





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 50X

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: ABB Страницы: 63

Бренд: XBOX Страницы: 4

Бренд: S-COM Страницы: 400

Бренд: Canarm Страницы: 3

Бренд: Unipulse Страницы: 99

Бренд: Accutrol Страницы: 25

Бренд: Mainpine Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: Harmonic Drive Страницы: 85

Бренд: QUNDIS Страницы: 2

Бренд: Gardena Страницы: 236

Бренд: Data Signs Страницы: 23

Бренд: Danfoss Страницы: 14

Бренд: Vega Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды