Vacon 500X, Руководство пользователя

Страница: 84 / 124

Tel. +358 (0)201 2121 • Fax +358 (0)201 212205
83
z
vacon vacon 500x parameters
7
705 Relay 1 Select
706 Relay 2 Select
707 DO1 Select
708 DO2 Select
Default: Drv Fault
Default: Drv Run
Default: Drv Ready
Default: At Speed
Range for Parameters 705-708: n/a
Levels 1, 2 for Parameters 705-706
Level 2 for Parameters 707-708
These four parameters configure what condition will cause relays R1, R2, DO1, and DO2 to activate.
Parameter 705 is associated with relay R1; parameter 706 with relay R2; parameter 707 with DO1; and
parameter 708 with relay DO2. The following values may be assigned:
Parameter Value Description
Drv ReadyThe drive is ready. (The relay will be open in Fault and Low Voltage conditions.)
Drv FaultA fault occurs. (If automatic fault reset and re-start is enabled, only faults that cannot be reset will activate
the relay. The relay will also activate for faults that can be reset when the number of re-start attempts exceeds the
value set in parameter
608 (Restart Number) .)
Drive RunThe drive has received a direction command.
Running FWDThe motor is running Forward and the output frequency is above 0.5 Hz.
Running REVThe motor is running in Reverse and the output frequency is above 0.5 Hz.
Zero SpeedThe drive is in Run mode, but the speed reference is 0 Hz.
At SpeedThe drive has reached reference speed.
Freq LimitThe drive limit is active when the speed commanded exceeds the value of parameter 306, Preset Freq 4.
Freq HystThis is active when the speed exceeds parameter 306 (Preset Freq 4) but is less than parameter 307 (Preset
Freq 5).
Current LimCurrent Limit mode is active.
High TempThe temperature limit of the drive has been exceeded.
Local ModeThe keypad is the control path for reference speed and control functions.
SeqOut-000Programmed sequence step active. SeqOut-
XXX values are all status
SeqOut-001outputs linked to a step in the program sequencer.
SeqOut-010
SeqOut-011See “Using the Vacon 500x Program Sequencer” on page 98 for more information.
SeqOut-100
SeqOut-101
SeqOut-110
SeqOut-111
Thres 1Active status of Threshold 1 for this output (see parameter 740 on page 85)
Thres 2Active status of Threshold 2 for this output (see parameter 743 on page 85)
Timer 1Active status of Timer 1 for this output (see parameter 746 on page 86)
Timer 2Active status of Timer 2 for this output (see parameter 749 on page 86)
ARCTICWhen a digital output is configured to use this option, the output will be active when the Arctic Mode is turning
on the DB resistor. This option will turn on when the temperature drops below the Arctic mode entry point, which is -
7°C. This will work even if Arctic Mode is not enabled.
DI-FWD
DI-REVDI-xxx values all refer to inputs on option cards;
DI-R/Jwhen the respective input is active, the respective
DI-ENoutput listed here is set.
DI-MOL
DI1
DI2 DI-x values all refer to inputs on the drive control board;
DI3 when the respective input is active, the respective
DI4 output listed here is set.
DI5
Reminder 1User-defined reminder
Reminder 2User-defined reminder
Reminder 3User-defined reminder
SIO ConfigIndicates the setting that the output will respond to, set in parameters 921 (SIO Imet Lvl) and 907
(Control Word)
TOD InhibitIndicates the drive is disabled based on the time set in TOD run enable parameters.
720 Active Logic Default: Active High
Range: n/a
Level 2