ENGLISH
- 7 -
PROGRAMMING
NOTE
: the first remote control to be memorised determines the
mode of operation; Royal or Personal Pass.
To change the operating mode, it is essential to perform a FULL
CODE ERASING and then memorise the new remote control.
m
IMPORTANT: to memorize the code in the correct way
it is necessary to keep a minimum distance of 1,5 metres
between the transmitter and the receiver’s antenna.
The self learning programming system enables the code
memorization and the setting of the following functioning modes:
MONOSTABLE
: it activates the corresponding relay through the
time of TX transmission. When the transmission stops, the relay
goes automatically off.
BISTABLE
: it activates the corresponding relay on the first TX
transmission. The relay goes off on the second transmission.
TIMER
: the tx transmission activates the corresponding relay
which goes off after the set time (max 7,5 minutes).
SELECTION OF THE RECEIVER CHANNEL
To select the channel of the receiver to be programmed, press
the P1 button for N times, as indicated in the table: the LED
corresponding to the selected channel turns on
SELECTED
CHANNEL
N°
IMPULSES P1
LED ON
1
2
3
4
CHANNEL 1
1
•
CHANNEL 2
2
•
CHANNEL 3
3
•
CHANNEL 4
4
•
PROGRAMMING OF THE MONOSTABLE
FUNCTION
WARNING: If the transmitter is ROYAL, before starting
programming, set the desired code on the transmitter.
Set the same code on all transmitters.
1.
Select the channel of the receiver to be programmed
2.
Within 5 seconds, press and hold the button on the remote
control.
-
if the remote control unit is a ROYAL version, the procedure
ends at point 3
-
if the remote control unit is a PERSONAL PASS version, go
to point 4 and follow the procedure until the end of the
section
3.
LED on the receiver is turned off to indicate the code has
been memorised correctly
4.
The led of the receiver goes out and goes on again: the code
has been memorised and the receiver remains standby for 5 s
with a new code to be memorised
5.
Memorise all the remote control units necessary
6.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
PROGRAMMING THE TIMER FUNCTION
WARNING: If the transmitter is ROYAL, before starting
programming, set the desired code on the transmitter.
Set the same code on all transmitters.
1.
Select the channel of the receiver to be programmes and hold
pressed the P1 button: the LED corresponding to the selected
channel will turn on for a few seconds
2.
When the led goes off, release the P1 button.
3.
The led starts a sequence of flashings at low speed (1 flash
per second). The number of flashing corresponds to the time
which can be set as shown in the table.:
N° Flashing
Time
N° Flashing
Time
1
01 sec.
17
1 min.
2
02 sec.
18
1,5 min.
3
03 sec.
19
2 min.
4
04 sec.
20
2,5 min.
5
05 sec.
21
3 min.
6
06 sec.
22
3,5 min.
7
07 sec.
23
4 min.
8
08 sec.
24
4,5 min.
9
09 sec.
25
5 min.
10
10 sec.
26
5,5 min.
11
11 sec.
27
6 min.
12
12 sec.
28
6,5 min.
13
13 sec.
29
7 min.
14
14 sec.
30
7,5 min.
15
15 sec.
31
BISTABLE
16
30 sec.
4.
Count the number of led flashings corresponding to the time
you wish to set
5.
Press the rx button P1 during the wished flashing: the
sequence of flashings stops and the led remains on
6.
Within 5 seconds, press and hold the button on the remote
control:
-
if the remote control unit is a ROYAL version, the procedure
ends at point 7
-
if the remote control unit is a PERSONAL PASS version, go
to point 8 and follow the procedure until the end of the
section
7.
The led on the receiver is turned off to indicate the code has
been memorised correctly
8.
The led on the receiver is turned off and then comes on
again: the code has been memorised and the receiver remains
standby for 5 s with a new code to be memorised
9.
Memorise all the remote control units necessary
10.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
Содержание Wally
Страница 2: ...1 J1 2 FIG 1 FIG 2 ...
Страница 27: ......
