0 3
A S S E M B L Y (see page 04)
F A U L T
C A U S E
R E M E D Y
⁄ Insufficient water
⁄ Supply pressure inadequate
⁄ Check water pressure (If a pump has been installed check
to see if the pump is working).
⁄ Regulator filter dirty
⁄ Clean filter in front of the mixer and on the MTC-thermo
cartridge
⁄ Shower filter seal dirty
⁄ Clean filter seal between shower and hose
⁄ contaminated dirt catch sieve in front of the backflow stop
⁄ Clean filters
⁄ Crossflow, hot water being forced into cold water pipe, or
vice versa, when mixer is closed
⁄ Backflow preventers dirty or leaking
⁄ Clean backflow preventers, exchange if necessary
⁄ Spout temperature does not correspond with temperature
set
⁄ Thermostat has not been adjusted
⁄ Adjust thermostat
⁄ Hot water temperature too low
⁄ Increase hot water temperature to 42 ºC to 65 ºC
⁄ Temperature regulation not possible
⁄ Temperature regulator dirty or calcified
⁄ Clean temperature regulator, exchange if necessary
⁄ For new installations: basic body incorrectly connected
(should be: cold right, hot left) or installed with 180º rota-
tion
⁄ change connections
⁄ Safety stop button not operating
⁄ Spring defective
⁄ push button calcified ⁄ contaminated
⁄ Clean spring and⁄or button, exchange if necessary
C L E A N I N G (see page 09)
S P A R E P A R T S (see page 08)
O P E R A T I O N (see page 06)
D I M E N S I O N S (see page 06)
M A I N T E N A N C E (see page )
⁄ To guarantee the smooth running of the thermostat, it is necessary from
time to time to turn the thermostat from total hot to total cold.
⁄ The mixer is equipped with check valves. The check valves must be
checked regularly according to DIN EN 1717 in accordance with na-
tional or regional regulations (at least once a year).
A D J U S T M E N T (see page )
After the installation, the output temperature of the thermostat must be
checked. A correction is necessary if the temperature measured at the output
differs from the temperature set on the thermostat.
S A F E T Y F U N C T I O N (see page )
The desired maximum temperature for example max. 42º C can be pre-set
thanks to the safety function.
Do not use silicone containing acetic acid!
S Y M B O L D E S C R I P T I O N
S A F E T Y N O T E S
Gloves should be worn during installation to prevent crushing and cutting injuries.
The product may only be used for bathing, hygienic and body cleaning purposes.
Children as well as adults with physical, mental and⁄or sensoric impairments must
not use this product without proper supervision. Persons under the influence of
alcohol or drugs are prohibited from using this product.
The hot and cold supplies must be of equal pressures.
I N S T A L L A T I O N I N S T R U C T I O N S
⁄ Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and tested as per the applicable
standards.
⁄ The plumbing codes applicable in the respective countries must be observed.
T E C H N I C A L D A T A
Operating pressure:
max. 1 MPa
Recommended operating pressure:
0,15 - 0,6 MPa
Test pressure:
1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
max. 70°C
Recommended hot water temp.:
65°C
Rate of flow by 0,3 MPa:
1 Consumer
approx. 44 l⁄min
2 Consumer
approx. 55 l⁄min
Thermal disinfection:
max. 70°C ⁄ 4 min
The product is exclusively designed for drinking water!
Safety against backflow
EN
