background image

STEP 1   

﹡﹡﹡

IMPORTANT NOTICE: 

DO NOT return to place of purchase!!! 
Please contact Customer Service hotline at 800-913-8999 for help

 

 

 

 

 

 

STEP 1 

1. Check the regulator to the propane tank connection 

remember the POL adapter is a left hand thread   

2. Check all connections on the hose regulator assembly   

3. Check the hose to the intake pipe to make certain that   

it is not kinked or in a position that could cause it to   

kink Tighten hand tight and than take a 1/2 turn with   

the adjustable wrench 

 

NOTE:

 The remaining connections are to be 

Tested after the heater has been lit   

(SEE LIGHTING INSTRUCTIONS) 

 

 

 

 

STEP 2 

4.

 

Check intake pipe fitting at the bottom of safety   

control valve 

5. Check pilot tubing to safety control valve   

6. Check orifice fitting and the safety control valve 

7. Check pilot tubing and pilot 

 

NOTE:

 After leak testing is completed   

and all leaks are sealed , close the door to   

the tank enclosure and your patio heater   

is ready to use. 

 

 

 

 

 

 

Page 8

 

ALWAYS CHECK THE FOLLOWING CONNECTIONS 

 

STEP 2   

      77 

    

SAFETY CHECKS   

Содержание PTH101






















Отзывы: