background image

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VERSION:

VT-CC1121-APR-2012

VT-CC1121-433M

VT-CC1121-433M

VT-CC1121-433M

VT-CC1121-433M

Questions

Questions

Questions

Questions and

and

and

and Answers

Answers

Answers

Answers

Description

Description

Description

Description

Reason

Reason

Reason

Reason and

and

and

and Solution

Solution

Solution

Solution

Can’t

communication

1

The power supply connect not well, check the module VCC whether it is out of maximum

rating.

2

The signal line connect not well, check the module SPI interface.

3

The settings of the transmitter module and receiver module are not the same. Check these

modules’ register configuration.

4

Signal block. If the transmitter work with a high TX power, and the receiver was put at a short

distance(<0.5m), maybe there is a signal block to make no communication.

Communication

distance is too

short

1

The application environment is too bad or the antenna is shield. Put the antenna to a better place

outside or higher throw a coaxial line , replace it with a higher gain antenna.

2

The work space contains a same frequency interference source, or a strong magnetic field

interference, power source disturbance. Try to change the carrier frequency or get far away from

the source of the disturbance.

3

The power supply is not strong. Check the voltage and the current whether it is enough.

High data error

1

The power supply ripple is too big, Change the power supply.

2

Check the module register configuration, it is recommended to set as the CC1121-datasheet.

3

There is a carrier frequency interference, change the channel.

4

The antenna unmatched to the module RF interface, change another matched antenna.

Development

Development

Development

Development Package:

Package:

Package:

Package:

1.

CC1121 datasheet

CC1121.pdf

2.

CC1121 register configuration tool

SmartRF Studio 7 v1.4.9.zip

3.

CC1121 demo code (CC1121 Demo Code.rar

4.

Hard ware tools

TI Chipcon Evaluation Board

Note

Note

Note

Note

1

1

1

1

You

You

You

You can

can

can

can get

get

get

get the

the

the

the development

development

development

development package

package

package

package above

above

above

above from

from

from

from the

the

the

the salesman

salesman

salesman

salesman when

when

when

when you

you

you

you order

order

order

order the

the

the

the module.

module.

module.

module.

2

2

2

2

As

As

As

As version

version

version

version update

update

update

update

please

please

please

please refer

refer

refer

refer to

to

to

to our

our

our

our latest

latest

latest

latest development

development

development

development materials.

materials.

materials.

materials.

Содержание VT-CC1121-433M









Отзывы: