manualshive.com logo in svg

UWT Rotonivo RN 4000 Series, Техническая информация/Инструкция по эксплуатации

Поделиться
Скачать
UWT Rotonivo RN 4000 Series Скачать руководство пользователя страница 7

page 

Level limit switch

Series RN 4000

Technical information / Instruction manual

Operating conditions

Ambient temp. (housing)

-20 .. +60°C  (-4 .. +140°F)
-40 .. +60°C  (-40 .. +140°F)   Version with heating of housing (pos.26)

Process temperature

-20 .. + 80°C  (-4 .. +176°F)
-40 .. +80°C  (-40 .. +176°F)   Version with heating of housing (pos.26)

Ventilation

Ventilation is not required

Min. powder density/ 

Sensitivity

see section “Sensitivity” on page 17

Signal delay

Version   

 

AC, DC, Multivoltage  

Universal voltage

Sensor free -> covered*  

ca. 1.3 sec 

 

ca. 1.5 sec + 0 .. 20 sec adjustable

Sensor covered -> free  

ca. 0.2 sec 

 

ca. 0.2 sec + 0 .. 60 sec adjustable

*after blocking of the measuring vane 

Features of bulk material

Hardly any limitations

Max. permitted mechanical 

torque (lateral)

Process connection aluminium:  

max. 50 Nm

Process connection plastics:   

max. 25 Nm

Protective measures in case of high loading: mounting of an protective canopy above the probe.

Max. tractive force

Pendulum shaft: 

400 N  (applicable only as full detector)

Rope extension: 

1.5 kN  (applicable only as full detector)

Max. process pressure

-0.9 .. +0.8 bar (-13.1 .. +11.6 psi) 
Versions with Ex-approvals: see remarks on page 19.

Vibration

1.5 (m/s

2

)

2

/Hz according to EN 60068-2-64

Relative Humidity

0 - 100%, suitable for outdoor use

Altitude

max. 2,000 m (6,562 ft) 

Expected product lifetime

Following parameters have a negative influence on the expected product lifetime: 
High ambient- and process temperature, corrosive environment, high vibration, high flow rate of 

abrassive bulk material passing the sensor element, high amount of measurement cycles.

Technical Data 

Transport and Storage

Transport

Observe the instructions as stated on the transport packaging, otherwise the products may get 
damaged.
Transport temperature:  -40 .. +80°C (-40 .. +176°F)
Transport humidity:  20 .. 85%
Transport incoming inspections must be caried out to check for possible transport damage.

Storage

Products must be stored at a dry and clean place. They must be protected from influence of corrosive 

environment, vibration and exposure to direct sunlight.
Storage temperature: -40 .. +80°C (-40 .. +176°F)
Storage humidity:  20 .. 85%

RN 4000

gi010121

7

Rotonivo

®

1

2

3

4

5

6

7

8

9

10

11

12

Содержание Rotonivo RN 4000 Series





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды