Utopia Lustre Скачать руководство пользователя страница 2

Installation 

Mark a horizontal line on the wall at the required height 

X---X

. Ensure  

that the wall brackets will fit inside the width of the cabinet and are  
equally spaced to ensure even distribution of weight. Secure the wall  
brackets to the wall using suitable fixings. 
 
Hook the unit onto the wall brackets so that the spring locks the arm  
into place. 
 
To alter the position of the cabinet on the wall, adjust the two screws  
in each hanging bracket. Adjusting screws A will move the cabinet up  
and down. When the cabinet is level on the wall, screws B will tighten  
the cabinet to the wall. 

 

 

 

Drawer Box Removal and Replacement 

To remove the drawer box, pull the drawer fully out and lift it upwards.  
To re-fit the drawer box, pull the runners fully out, place the drawer  
box on the runners and push it rearwards until it clicks into place. 
 

Drawer Front Removal 

Slide the slide the drawer side covers rearwards to expose the  
screws. Using a crosshead screwdriver, turn the screws shown to  
release the drawer front. Where there are two screws on each  
drawer side, turn the top screw first followed by the bottom one. 

 

Drawer Front Adjustment 

Slide the drawer side covers rearwards to expose the adjustment  
screws. To raise or lower the drawer front, turn the larger screws  
with a crosshead screwdriver until adjusted as required. To move  
the drawer front from side to side, turn the smaller screws. To adjust  
the tilt of the drawer front, remove the caps from the tops of the drawer  
sides. Use a cross-head screwdriver to adjust as required. 

 

Care & Maintenance 

Furniture should be regularly dusted with a soft cotton or micro-fibre cloth. For more thorough 
cleaning, occasionally wipe your furniture with a soft cloth dampened with a mild detergent 
solution. Surfaces should be thoroughly dried with a lint free cloth to prevent watermarks. Under 
no circumstances should solvent cleaning agents, bleach or abrasive cleaning agents or cloths be 
used. Spills should be removed immediately using a clean cloth. All bathroom furniture will 
deteriorate through prolonged periods of exposure to high levels of condensation so bathrooms 
must be adequately ventilated using suitable extraction. Failure to ensure adequate ventilation 
may invalidate your guarantee.   
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Lustre













Отзывы: