Utilitech 0407161 Скачать руководство пользователя страница 11

WARRANTY

11

Lowes.com

®

Limited Warranty

This Limited Warranty is effective June 1, 2011 and replaces all undated warranties and warranties dated before June 1, 

2011.
The Manufacturer warrants to the original consumer purchaser (“Purchaser” or “You”) that its products are free from 

defects in material and workmanship for a period of twelve (12) months from the date of the original consumer purchase. 

If, within twelve (12) months from the original consumer purchase, any such product shall prove to be defective, it shall 

be repaired or replaced at the Manufacturer’s option, subject to the terms and conditions set forth herein. Note that this 

limited warranty applies to manufacturing defects only and not to ordinary wear and tear. All mechanical devices need 

periodic parts and service to perform well. This limited warranty does not cover repair when normal use has exhausted the 

life of a part or the equipment.
The original purchase receipt and product warranty information label are required to determine warranty eligibility. 

Eligibility is based on purchase date of original product – not the date of replacement under warranty. The warranty 

is limited to repair or replacement of original purchased product only, not replacement product (i.e. one warranty 

replacement allowed per purchase). Purchaser pays all removal, installation, labor, shipping, and incidental charges.
For parts or troubleshooting assistance, DO NOT return product to your retail store - contact the Manufacturer’s Customer 

Service at 866-994-4148.
Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail 

outlet where it was purchased or to the factory immediately after the discovery of any alleged defect. The Manufacturer 

will subsequently take corrective action as promptly as reasonably possible. No requests for service will be accepted if 

received more than 30 days after the warranty expires. Warranty is not transferable and does not apply to products used 

in commercial/rental applications.

Sewage Pumps

DO NOT return a sewage pump (that has been installed) to your retail store. Contact the Manufacturer’s Customer 

Service. Sewage pumps that have seen service and been removed carry a contamination hazard with them. 
If your sewage pump has failed:
•  Wear rubber gloves when handling the pump; 
•  For warranty purposes, return the pump’s cord tag and original receipt of purchase to the retail store;
•  Dispose of the pump according to local disposal ordinances. 

Exceptions to the Twelve (12) Month Limited Warranty

Product

Warranty 

Period

UT25PCP

2 Years

General Terms and Conditions; Limitation of Remedies

You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does 

not apply to the following: (1) acts of God; (2) products which, in the Manufacturer’s sole judgment, have been subject to 

negligence, abuse, accident, misapplication, tampering, or alteration; (3) failures due to improper installation, operation, 

maintenance or storage; (4) atypical or unapproved application, use or service; (5) failures caused by corrosion, rust or 

other foreign materials in the system, or operation at pressures in excess of recommended maximums.
This warranty sets forth the Manufacturer’s sole obligation and purchaser’s exclusive remedy for defective products.
The Manufacturer’s SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES 

WHATSOEVER.
THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED 

WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 

FOR A PARTICULAR PURPOSE. THE FOREGOING LIMITED WARRANTIES SHALL NOT EXTEND BEYOND THE 

DURATION PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an 

implied warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal 

rights and You may also have other rights which vary from state to state.

866-994-4148

Содержание 0407161

























Отзывы: