manualshive.com logo in svg

UTICA BOILERS UH15B-060K, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
UTICA BOILERS UH15B-060K Скачать руководство пользователя страница 38

38

APPENDIX A - CONTROL MODULE

A.6 Boiler High Limit Temperature Controller

• When water temperature reaches setpoint, controller 

ends heating cycle. 

• When water temperature drops below setpoint minus 

differential, controller restarts heat cycle to re-heat 

boiler water.  

• If water temperature exceeds maximum allowed 

temperature (220°F or 104°C), controller enters manual 

reset lockout state. (Automatic reset on S9361A2098)

• For models having reset capability, press any onboard 

button or cycle power to reset.

A.7 Troubleshooting 

• Following service procedures are provided as general 

guide. 

• On lockout and retry models, meter readings between 

gas control and ignition module must be taken within 

trial for ignition period. Once ignition module shuts 

off, lockout models must be reset through key buttons 

and display.  On retry models, wait for retry or reset at 

thermostat.

• Check for correct installation and wiring before replacing 

any component.

• Control module cannot be repaired. If it malfunctions, it 

must be replaced.

• Use only qualified service agent to service ignition 

systems.

1. 

Perform checkout as first step in troubleshooting.  

Check troubleshooting guide to pinpoint cause of 

problem. See Table A2.

2. 

If troubleshooting indicates ignition problem, see 

Ignition System Checks to isolate and correct the 

problem.  

3. 

Perform checkout procedure following troubleshooting 

guide again to verify system is operating normally.

A.8 Troubleshooting Error Codes

Integrated boiler control uses advanced diagnostic 

capability to assist in troubleshooting error conditions.  

Figure A1 shows codes that could arise on integrated 

display during fault.  

Suggestions are provided in Figure A1 page 36 and Table 

A2 for servicing these potential errors.

Figure A-3 - Basic Control Algorithm Example

 PN 240012809, Rev. D [08/15/2021]

Содержание UH15B-060K

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды