UTICA BOILERS MACF-115 Скачать руководство пользователя

Страница: 45 / 139

8.4 Access To Connection Block

Ensure there is no line voltage at boiler.

Lift and remove front cover. Remove screws (2)

from cover on junction box located on boiler's left

side. Remove junction box cover.

Guide controller or thermostat wire through round

grommet(s) located on top panel of boiler.

Tilt control box forward by opening holding clip

located on left side of control housing.

Expose M1 and M2 terminal blocks by removing

screw from plastic cover on left. See Figure 8-3.

Remove plastic from channel in plastic cover. Run

wires through new opening.

Connect wires to appropriate terminals on

connection block.

Tilt control box back to original position. Ensure clip

on left side of control box is fully engaged.

Replace front cover and cover to junction box.

10.

Turn power to boiler on.

Dry contact end switches from various manufacturers

can be attached to boiler control PCB.

8.5 Main Supply Connection

Main supply is connected to terminal block

which is

high voltage (120V / 60Hz).
Fuses, 3.15 A, are incorporated in the power supply

terminal block. To check or replace fuse pull out black

fuse carrier.

TERMINAL BLOCK M1

(L) = Live (brown)
(N) = Neutral (light blue).

= Ground (yellow-green).

(1) (2) = contact for 120V Room Thermostat.
Place jumper back on terminals 1-2 of boiler terminal

block

if room thermostat is not used or if Remote

Control is not installed.

FIGURE 8-2 Terminal Block Locations

Fuse Holders (2)

DANGER

Electrocution Hazard! HIGH VOLTAGE -

Connections in terminal block M1 are high

voltage (120V / 60Hz). Before making

connections, verify appliance is disconnected

from power supply. Respect the input polarity

on terminal block M1: L (LINE) - N (NEUTRAL).

Failure to follow these instructions WILL result in

death or serious injury.

FIGURE 8-3 Terminal Plastic Cover with Knockouts

Remove

New Opening

8 - ELECTRICAL CONNECTIONS

TERMINAL BLOCK M2
Terminals 1 - 2

: Buss connection of Open Therm

Gateway for ECR programmable room unit thermostat

Terminal 3 :

Not used on Combi units

Terminals 3 - 4

: Indirect storage tank sensor

connection for heat-only boilers

Terminal 4 - 5:

Outdoor temperature sensor

connection (supplied as an accessory)

Terminals 6 - 7 - 8:

24V room thermostat connection

Terminals 9 - 10:

0 - 10V connection

240013371 REV B, [10/01/2021]

Содержание MACF-115












































































































































Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды

UTICA BOILERS MACF-115, Руководство пользователя

Результаты поиска

Содержание MACF-115

Отзывы:

Похожие инструкции для MACF-115

Бренды по названию

Популярные бренды