连接接口
连接接口
3
4
Please confirm if the installation is correct;
Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B
industry standards;
The power supply of each PoE port is no more than 30W; please do not connect the PoE
device which exceeds the maximum PoE power supply;
Please replace a failure device with a properly functioning one to check if the device is
broken;
If the problem still exists, please contact the factory.
Item
UTP3-GSW04-TP60
Power
Supply
Power
Supply
Power
Adaptor
Voltage
Range
DC48V~57V
Power
Consumption
60W
Connector
Parameters
PortsEthernet
1
～
4
Downlink
Ports:10
/
100
/
1000Mbps
PoE
Ethernet
Ports;
5
～
6
Uplink
Ports:10
/
100
/
1000Mbps
Ethernet
Ports.
Transmission
Distance
0
～
100m
PoE
Standard
IEEE802
.
3 af, IEEE802
.
3
at, End
-
span
PoE Power Supply
Each Port
≤
30W, Total
<
60W
Network
Switching
Network
Standard
IEEE
802
.
3
,
IEEE
802
.
3u
,
IEEE
802
.
3ab
Packet Forwarding
Rate rate
8
.
93Mpps
Switching Capacity
12G
Packet
Data Cache
1Mb
MAC Table
8K
One
-
key
CCTV Mode
Mode
Function
a. All Downlink Ports Can Only Communicate with Uplink
Ports, Can’t communicate each other;
b. Restrain Network Storm under 2M.
Indicator
Status
Power
Input
1x
Red Light
One-key CCTV
1x Green Light, Solid on after CCTV Mode on
Downlink
Ports
Link: Green LED( on
PoE: Yellow LED( on RJ45)
RJ45)
Uplink
Ports
Link:Green LED(on RJ45)
Acting:Yellow LED(on RJ45);
Protection
Level
Lightning Protection
6KV
,
Per
:
IEC61000
-
4
-
5
ESD Protection
Level 3, 1a
Contact
Discharge
Level 3, 1b
Air
Discharge
Per
:
IEC61000
-
4
-
2
Operation
Environment
Operation
Temperature
-10
~+
45
℃
℃
Storage
Temperature
-
40
~+
85
℃
℃
Humidity
(
Non
-
condensing
)
0
~
95
%
Mechanics
Dimension
(
LxWxH)
135
mm×86
mm×27mm
Material
Metal
Color
Black
Weight
343g
4
Ports Full Gigabit PoE Switch
4
Ports Full Gigabit PoE Switch
Specification
RJ
45
Making
Method
Tools to make RJ45: wire
crimper, network tester.
Wire sequence
of
RJ45
plug should conform with EIA/TIA568A or EIA/TIA568B standard.
1) Strip off the 2cm insulating layer to expose the 4 pairs UTP cable;
2) Seperate the 4 pairs of UTP cable and straighten them;
3) Line up the 8 separated pieces of cables per EIA/TIA 568A or 568B;
4) Cut the cables to leave 1.5cm bare wire and make sure 8 thread ends are flat and neat ;
5) Insert 8 cables into RJ45 plugs, make sure each cable is inserted in each pin;
6)Then use wire crimper to crimp the RJ45;
7) Do the above 5 steps again to make the another end of the twisted pair and make sure
consistent cable order between two ends ;
8) Using network tester to test the cable.
P
in
color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
Pin
color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A
EIA/TIA 568B
Notice
Make sure both ends use EIA/TIA568A connection method when using RJ45 port.
Make sure both ends use EIA/TIA568B connection method when using RJ45 port.
连接接口
Trouble
Shooting
Please find the following solution when the device doesn't work
Product specifications subject to change without prior notice.
