UTE Electronic UH2-44-SET Скачать руководство пользователя страница 67

Страница: 67 / 76

UH2-44: 4x4 HDMI 2.0 HDBaseT Matrix Switcher

U.T.E. electronic GmbH & Co. KG

www.ute.de

Crosstalk Isolation

SPDIF:

< -70 dB, 10KHz sine at 0dBFS level (or max level

before clipping).

L+R:

< -80 dB, 10KHz sine at 0dBFS level (or max level

before clipping).

L-R Level Deviation

L+R:

< 0.3dB, 1KHz sine at 0dBFS level (or max level

before clipping).

Frequency Response
Deviation

< ± 0.5dB 20Hz - 20KHz.

Output Load Capability

L+R:

1KΩ and higher (Supports 10x paralleled 10KΩ

loads).

Stereo Channel
Separation

>70dB@1KHz.

Noise Level

L+R:

-80dB;

SPDIF:

-90dB

Control Part

Control port

(4) IR IN, (1) IR ALL IN,
(4) IR OUT, (1) IR ALL OUT,
(1) IR EYE,
(5) RS232,
(1) FIRWARE,
(1) TCP/IP

Control Connector

(11) 3.5mm jacks, (5) 3-pin terminal blocks, (1) Type-A
USB, (1) RJ45

General

Transmission Mode

HDBaseT

Transmission Distance

1080p ≤ 230 feet (70 meters),
4K

@60Hz ≤ 131 feet (40 meters)

Bandwidth

18Gbps

Operation Temperature

-5

℃

~ +55

℃

Storage Temperature

-25

℃

~ +70

℃

Relative Humidity

10% ~ 90%

External Power Supply

100V~240V AC, 50/60Hz

Power Consumption

65W (Max)

Dimension (W*H*D)

436.4mm x 44mm x 356.6mm

Net Weight

3.3kg

Содержание UH2-44-SET












































































Результаты поиска

Содержание UH2-44-SET

Отзывы:

UTE Electronic UH2-44-SET, Руководство пользователя, Страница: 67 / 76

Результаты поиска

Содержание UH2-44-SET

Отзывы: