background image

 

7

 

WARNING 

 

At 60

°

C (140

°

F) hot water can produce third 

degree burns in 6 seconds; at 54

°

C (130

°

F) in 30 

seconds. Maximum thermostat setting is 41

°

(106

°

F). 

 
 

2.4.1) Precautions 

against 

freeze-ups 

 
To avoid damage to the swimming pool heater, pump, filter, piping and 
other accessories, make sure that the circulating pump is "ON" and that 
there is adequate circulation of water through all these components to 
prevent freeze-up when the outside temperature is below 0°C (32°F). If 
the swimming pool heater is to be turned off at temperatures below the 
freezing point, the water piping at the inlet and outlet of the swimming 
pool heater must be disconnected. Also, it must be drained by opening 
the drain valve at the bottom as well as the air vent, to allow the 
introduction of air into the primary circuit of your pool heater. Then, the 
feed water line must be bled by removing the 1/2’’ NPT plug (I) located 
at the bottom of the T fitting located after the water feeder and regulator 
device. 
 
 

2.5) 

SHUT DOWN AT THE END OF THE 
SWIMMING SEASON 

 
 

2.5.1) Outside 

installation 

 
1.  Make sure that the HMP-03 ON-OFF switch (D) and the 

circulating pump switch are OFF; 

2. 

Make sure that power supply switch is OFF; 

3. 

Disconnect the water inlet and outlet of the HMP-03 swimming 
pool heater; 

4. 

Open the drain valve (O) located on the bottom of the HMP-03 
unit and drain it completely; 

5. 

Removed the ½’’ plug (I) from the T fitting located on the right end 
side of the water feeder & regulator device (J); 

6. 

Leave the drain valve open during all shut down periods. 

 
 

2.5.2) Inside 

installation 

 

3. 

For inside installations protected from freezing, we suggest you 
follow the same procedure than article 2.5.1 at the exception that 
you can leave it full of water for the winter shutdown period. This 
apply only for an installation protect against cool temperature. 

 
 

2.5.3) Prolonged 

non-use 

or 

winterization 

of the oil burner 

 
When the oil burner will not be used for an extended period of time OR 
the appliance is not used altogether, follow this procedure: 
 
1) 

Close the valve located at the bottom of the oil tank that feeds the 
burner; 

2) 

Raise the thermostat to call for heat and cause the oil burner to 
start; 

3) 

Let the burner fire until there is no longer a flame and combustion 
is cut by the safety (usually 30 to45 seconds after the flame 
extinguishes) 

4) 

Depress the red Re-start Button; the burner should start. If there is 
still a flame, repeat the procedure until there is no more flame. 

5)  When you have assured yourself that steps 3) and 4) are 

completed, shut-off the electrical power to the unit. 

2.6) 

START-UP AT THE BEGINNING OF THE 
SWIMMING SEASON 

 
Have the chimney and the connecting pipes swept (INSIDE 
INSTALLATION ONLY). 
Have all heating surfaces cleaned if deemed necessary after a visual 
check. To clean the tubes of the heat exchanger, remove the smoke 
box and the flue baffles. 
 
 

CAUTION 

The HMP-03 being equipped with a sound trap, 
make sure not to damage the acoustical material 
when cleaning the boiler. The use of a flexible 
cleaning brush is strongly recommended. 

 
 
1. 

To clean the combustion chamber removes the burner; 

2. 

Replace the oil filter and nozzle; 

3.  Have the burner electrodes cleaned along with the burner 

retention head; 

4. 

Close the drain valve (O), install the ½’’ plug (I) to the T fitting and 
install the inlet and outlet water pipes as showed in figure 3; 

5. 

Make sure that oil valve is open; 

6. 

The power supply interrupter should be "ON"; 

7.  Start the filter pump and wait until the air is completely bled 

through the HMP-03 unit; 

8. 

Select the "ON" position on the HMP-03 switch located on the 
front panel; 

9. 

Refer to section 2.2 for the burner start up. 

 
 

2.6.1)  Regular maintenance during 

the heating season 

 
 

2.6.2) Nozzle 

 
3. 

A dirty or clogged nozzle can prevent ignition or cause odors 
and smoke. It must be replaced. 

 
 

2.6.3) Fuel 

tank 

 
Regularly check the level tank. Should it run dry, the lines will have to 
be bled before restarting the burner. 
 
 

2.7) PRECAUTIONS 

 
Never use your swimming pool heater as an incinerator. Never pile or 
store paper or garbage near it. 
 
 
 

Содержание ICP HMP-03














Отзывы: