background image

3

IT IS YOUR OR THE INSTALLER’S RESPONSIBILITY TO READ ALL SAFETY PRECAUTIONS 

AND FOLLOW THE PRESCRIBED DIRECTIONS�

When properly maintained and operated your stove should give you many years of service.  How-

ever there are important safety aspects of these products that you need to be aware of when oper-

ating a wood stove.
1. ONLY USE SOLID WOOD FUEL. NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, 

KEROSENE, CHARCOAL LIGHTER FLUID, NAPHTHA, ENGINE OIL, OR SIMILAR LIQUIDS 

TO START OR ‘FRESHEN UP’ A FIRE IN THIS STOVE.  KEEP ALL SUCH LIQUIDS WELL 

AWAY FROM THE STOVE WHILE IT IS IN USE.  DO NOT BURN GARBAGE IN THE STOVE.

2. The burning of wood gives off gases which can be extremely dangerous. The stove is designed 

that under normal operating circumstances these gases pass up the flue chimney system and 

cannot escape into your home, however it is important that your flue system is properly installed 

and that you check all joints regularly to ensure that there are no cracks or gaps, check the door 

sealing  rope  and  replace  when  damaged.  We  recommend  a  smoke  alarm  be  fitted  in  rooms 

where stoves are installed. Do not use stove in a room where negative pressure conditions may 

occur, such as through the use of extraction fans unless an adequate air supply into the room is 

ensured, as this may draw air through the stove and cause products of combustion to escape into 

the room.

3. Creosote and soot may accumulate in your flue pipe and chimney. This may ignite, causing a 

chimney fire. If you suspect a chimney fire evacuate people from the building, close down the 

air controls on the stove and call the Fire Department. To prevent the accumulation of soot or 

creosote, check flue and chimney regularly and clean as necessary. Good burning, hot stoves 

will generally cause a lot less build-up than slow burning stoves. Likewise dry wood will cause 

less build-up than wet wood. We recommend a fire extinguisher be available where stoves are 

in operation. In the event of a chimney fire do not re-light the stove until it and the flue chimney 

system have been thoroughly checked and repaired as necessary.

4. Stoves get extremely hot and should not be touched when lit. When young children are in the 

area, we recommend the use of a suitable fire guard around the stove. Always wear protective 

gloves when reloading stove.

5. Never over-fire your stove. If external parts of your stove are glowing red then the stove is over-

firing and your draft settings should be reduced. Never interfere with the draft mechanisms or 

adjust your air settings outside those limits set when the stove is manufactured. Never use a fan 

to supply air to the stove or to extract air from it.

6. All users of the stove should be aware of the contents of this manual. Please leave this manual 

where it is accessible to stove users and do not allow anyone to use the stove that is unfamiliar 

with its correct operation.

7. Never use the stove if any parts are missing or damaged, only use genuine parts as replace-

ments. Never modify your stove.  

8. DO NOT INSTALL IN A MOBILE HOME.

We hope you have many years of warmth and comfort from your stove 

but please do so safely�

Stove Safety

Содержание Brunswick 3800PB





















Отзывы: