manualshive.com logo in svg

USC U-Batch, Руководство оператора

Поделиться
Скачать
USC U-Batch Скачать руководство пользователя страница 40

Page 40 

U-BATCH™ TREATER 

H-O-A PUMPS SCREEN 

1. PUMP 1 H-O-A MODULE:  

This module controls the function of the liquid pump     

motor.  The HAND button will place the pump motor on in the manual mode of          
operation.  When it is active it will turn yellow.  The OFF button will turn the motor off  
in the manual mode of operation.  When it is active it will turn red.  The AUTO  button 
will place the device in the automatic mode of operation.  When it is active it will turn 
green.  Pressing the REVERSE PUMP button will place the pump in HAND mode but 
the pump will be running backwards. 

2. LIQUID PURGE MODULE:  

This module controls the function of solenoid for the 

compressed air used to clean the supply line.  The HAND button will place the solenoid  
in the manual mode of operation.  When it is active it will turn yellow.  The OFF button 
will switch the solenoid to the closed position.  When it is active it will turn red.         
The AUTO button will place the device in the automatic mode of operation.                     
When it is active it will turn green. 

3. POWDER :  

Press the Run Time button and use the numeric keypad to enter the 

number of seconds for the air to run while delivering powder from the hopper to the top 
of the mix hopper.  Pressing the START button engages the solenoid to begin air flow 
to the supply line of the powder delivery hopper.  

4. PUMP MOTOR PERCENT SPEED: 

When this button is pressed, a numeric touch   

pad will appear to allow the operator to adjust the speed of the liquid mix motor.           
It drives the motor to a specified percentage of the maximum pump speed. 

 

1 

2 

3 

4 

Содержание U-Batch























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды