US Shift Quick4 4R100 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

background image

26

Shift Buttons with Momentary On / Off Switch

For this configuration, you will need to connect the Dark Blue wire (Pin 14 on the
Vehicle Connector) to your down-shift button (momentary) and connect the Light
Blue wire (Pin 6 on the Vehicle Connector) to your up-shift button (momentary).
To connect the on / off switch (momentary), solder one side of the switch onto
the Dark Blue down-shift wire and the other side to the Light Blue up-shift wire.
(Follow the guidelines for soldering found in the “General Installation” section.)
Remember that the correct settings must be used in Shiftware. To enable
Manutronic, press the On/Off button once and do the same to disable it.

«
...
24
25
26
27
28
...
»

Содержание Quick4 4R100













































Отзывы:

Нет отзывов

Похожие инструкции для Quick4 4R100

Бренд: Panasonic Страницы: 92

Бренд: Panasonic Страницы: 16

Sportsound SSR-300

Бренд: Daktronics Страницы: 6

Бренд: Comica Страницы: 52

Бренд: Jensen Страницы: 41

Бренд: CSI Страницы: 1

Бренд: Anker Страницы: 19

Бренд: Icom Страницы: 8

Бренд: Sennheiser Страницы: 10

Бренд: Scott Страницы: 29

Bell'O Digital BDSW-1650-BLK

Бренд: Twin-Star International Страницы: 20

Бренд: X4-TECH Страницы: 2

Бренд: JVC Страницы: 92

Electra Elite BLF

Бренд: NEC Страницы: 14

Бренд: NEC Страницы: 24

Бренд: NEC Страницы: 31

Бренд: NEC Страницы: 75

Бренд: Sharp Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды