16. ON/OFF BUTTON (PITCH)
Press the button to be PITCH ON mode, press it again on the
PITCH ON mode, and blinks with unit on the PITCH OFF mode.
17. 3 HOT-CUE
This unit will allow you to play from 3 cue points instantly.
Set CUE memory: Press the MEMO button first, and then press the
CUE button to complete the CUE setting, then this CUE button will
light up. Play” CUE” memory: Upon pressing specific CUE button,
it will flash about 5 seconds.
Note: This function is not available during perform REVERSE sound effect.
18. SAM. BUTTON
Sampler is a kind of sound effect that you record the music from the track.
While playing the music, you can use the sampler to mix with music.
The maximum length is 32 seconds.
Set start point: Press the MEMO key, and then press SAM button,
after memorizing the SAM button flashes quickly (2 times in 1 sec)
Set End point: Press the SAM button again, when the end point is memorized,
the SAM button lights up (not flash).
Play Sampler: During PLAY mode, press the SAM button, then the button
will flash slowly. (1 time in 1 sec)
NOTE: Refer to parameter setting instruction for sampler adjustment
19. JOG WHEEL
*Speed Control (SEARCH indicator off)
Rotating the wheel, in play mode, will change the playback speed accordingly.
While rotating clockwise, the player speed increase; rotating counterclockwise,
the speed decrease.
*Search (SEARCH indicator lights)
Rotating the wheel, the player will forward or backward quickly.
The searching speed changed according to the dialing speed.
It can be carried out by one frame increment.
20. Seamless Loop (2 set)
There is A, B/LOOP/ EXIT, RELOOP buttons.
1. A BUTTON—-“start point” (A point. Also, Cue 1 could be A point)
After setting up the A point, the red Led light up.
2. B/LOOP/ EXIT BUTTON: —-“ End point”(B point). Press the B /LOOP
button to set up the B point and start the loop playback automatically.
Loop lights on the display and the 3 LEDs flash. Press this button
again to exit the LOOP playback.
3. Return to the loop playback by pressing the RELOOP while
in performance. However, if your want to return to loop playback,
you can press RELOOP BUTTON
4. Change “ START POINT” and” END POINT” by pressing the
A& B/ LOOP/ EXIT button again
5. The interval between A and B point must be more than 20 frames;
otherwise, the B point will be canceled, then LOOP function disappear and
LOOP fades on the display
SOUND EFFECT/ DIRECT ACCESS BUTTONS
* SOUND EFFECT OFF
The buttons are direct access keys (0~9).
To select the number of the
track you would like to play.
* SOUND EFFECT ON
The buttons is for sound effect control and it lights up when the sound effect
be chosen and off when the button is pressed again.
NOTE:
How to set up the parameter; please refer to parameter
setting instruction. (Page
7)
SCRATCH:
Move the JOG Wheel backward or forward like scratching
a turntable record.
This sound effect can be performed independently, or in parallel with other effect.
BRAKE:
To change the speed of PAUSE and START. This sound effect can be
performed independently, or in parallel with other effect.
REVERSE:
The music is playing backward. This sound effect can be performed
independently, or in parallel with other effect.
PHASER:
It sounds like the airplane takes off
FLANGER:
It sounds like another kind of airplane takes off. .
FILTER:
There are bass & treble. To increase the parameter value, it will cut bass off
but keep treble. To decrease the parameter value, it will cut treble off but keep bass.
CHOP:
The music is chopped with break.
PAN:
Alternatly playing right and left signal
ECHO:
Have the effect as ECHO.
22. SOUND EFFECT ON/OFF SWITCH
Press the EFFECT button to activate or deactivate the sound effect.
While the effect is activated, on the display the mark ? above the effect is light.
.
23. EFFECT SELECT KNOB
The parameter of sound effect can be pre-set. Turn the knob until the LCD shows
the effect name that you want, push the button to select it, and turn this button
again to select from the menu for setting parameter.
24. EFFECT SCOPE KNOB
After the menu of effect is selected, turn this knob to choose the parameter,
the relative value can be shown in the LCD.
(Please refer to page
7
with the Parameter Setting Instruction for details)
When the unit is not under parameter adjustment, the display does not show the
effect name, this knob can be used to adjust the KEY scale, and press it to
lock the key (the display will show)
25. RELAY
Press the “RELAY” button to activate. When one unit is in play mode, and
the other unit is in “pause” mode; pause the playing unit, the other
unit will automatically start to play (the button will blink).
26. BPM BUTTON
You can get the BPM number automatically or manually. Pressing the
BPM BUTTON for 3 seconds to switch between auto and manual control.
The BEAT will be shown on the display! Under the manual mode, tapping this
button to get the beat value.
27. KEY ON/OFF SWITCH
Press the button to switch KEY mode on or off.
• KEY OFF: The display shows the “KEY” in blinking, and the key changed
according to the pitch change. The key parameter adjustment is not in effect
• KEY ON: The “KEY” lights on the display, turning the SCOPE knob to adjust
the key. Slide the pitch slider will also change the key.
• KEY LOCK: Press the SCOPE knob to lock the key as set, sliding the pitch
slider does not change the key.
Please refer to parameter setting instruction. (Page
8
)
28. CARD:
Switch the playback source to memory card.
29. CONNECTOR PORT
The 8-pin(6-pin) termination permits the connection of the
control unit to the main unit.
30. SLEEP:
Leave the unit unused for 30 minutes; the machine will shut off automatically.
6
