background image

DS1043-103M

 

14

 

LBT8039

 

 

TECHNICAL SPECIFICATIONS 

 

ELECTRICAL CHARACTERISTICS 

Mains voltage: .......................................................................................................................... 

 10% - 15% 50hz

 

Load output voltage (VOUT): ................................................................................................................................. 

27.6Vdc

 

Maximum output current:................................................................................................................. 

2.5A for Ref.1043/191

 

 

4A for Ref.1043/192 

Battery charger voltage: ........................................................................................................................... 

27.6Vdc @ 20°C

 

Battery charger maximum current: ............................................................................................................................... 

0.8A

 

Consumption of power supply equipment only (without VOUT OUTPUT load): ........................................................ 

0.08 A 

 

FUSES 

The following tables indicate the characteristics of fuses present on the two power supply units. 

Exclusively use fuses with these following characteristics! 

 

Fuse for Ref.1043/191: 

Description 

Use 

Current 

Voltage 

Type 

Dimensions 

Fuse inserted  in mains terminal fuse 
holder  

Mains input  

0.8 A

 

250V

 

T

 

5 x 20

 

Fuse  inserted  in fuse holder  on battery 
connection cable  

Batteries power supply 
input  

3.5A 

250V 

5 x 20 

 

Fuse for Ref.1043/192: 

Description 

Use 

Current 

Voltage 

Type 

Dimensions 

Fuse inserted  in mains terminal fuse 
holder  

Mains input  

1 A 

250V 

5 x 20 

Fuse  inserted  in fuse holder  on battery 
connection cable  

Batteries power supply 
input  

5A 

250V 

5 x 20 

 

NOTE:

 T = delayed 

 

BATTERIES 

In the power supply equipment must be installed two batteries used as backup source in case  of blackout. The batteries 
must be lead sealed type, for backup use. Exclusively use this kind of batteries. Disconnect the mains before opening the 
batteries  compartment.  Follow  the  safety  standards  described  in  the  chapter  GENERAL  SAFETY  STANDARDS  of  this 
manual. 

Warning: do not reverse polarity! 

 
Urmet batteries code: ............................................................................................................... 

1033/601 for Ref.1043/191 

 

1033/602 for Ref.1043/192 

Batteries voltage (each): .............................................................................................................................................. 

12 V 

Batteries capacity (each): ................................................................................................................. 

7Ah for Ref.1043/191

 

 

15Ah per Ref.1043/192 

Batteries charge time:  ............................................................................................................................. 

80% in 24 hours

 

 

remaining 20% in  successive 24 hours 

Maximum internal resistance  .............................................................................................................. 

1 ohm for 1043/191 

0.7 ohm for 1043/192 

 

ENVIRONMENTAL AND MECHANICAL CHARACTERISTICS 

Operating temperature range:  ....................................................................................................................  

–5°C to +40°C

 

Relative humidity:  .............................................................................................................................................  

5% to 93%

 

Installation: ............................................................................................................................................................... 

indoor 

Protection degree  ........................................................................................................................................................ 

IP30 

Dimensions  ........................................................................................................................................... 

460x340x130 mm

  

Weight:   ........................................................................................................................................ 

8.2 kg for Ref.1043/191 

 

9.4 Kg for Ref.1043/192 

Содержание 1043

















Отзывы: