background image

4.

Hanging the Fan

REMEMBER 

to turn off the power. Follow 

the steps below to hang your fan properly:

Step 1. 

Remove the decorative canopy bottom

cover from the canopy by turning the cover 
counter clockwise.(Fig. 5)

Step 2. 

Remove the mounting bracket from 

the canopy by removing the 1 of 2 screws 
from the bottom of the mounting bracket and 
loosening the other one a half turn from the 
screw head. Next, turn the canopy counter 
clockwise to removing the mounting bracket 
from the canopy. (Fig. 5)

Step 3. 

Pass the 120-volt supply wires 

through the center hole in the ceiling hanger 
bracket as shown in Fig. 6.

Step 4. 

Secure the hanger bracket to the 

ceiling outlet box with the screws and 
washers provided with your outlet box.

Step 5. 

Remove the hanger pin, lock pin and 

set screws from the top of the motor 
assembly. (Fig. 7)

Step 6. 

Route the safety cable and wires 

exiting from the top of the fan motor through 
the coupling cover, canopy cover and canopy 
and then through the ball / downrod. (Fig. 7)

Step 7. 

Align the holes at the bottom of the 

downrod with the holes in the collar on top of 
the motor housing (Fig. 7). Carefully insert 

the hanger pin through the holes in the collar and 
downrod. Be careful not to jam the pin against the 
wiring inside the downrod. Insert the locking pin 
through the hole near the end of the hanger pin until it 
snaps into its locked position, as noted in the circle 
inset of Fig. 7.         

 

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 7

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.  

 

Figure 6

Figure 7

Ceiling 

hanger

bracket

Mounting screws 

(supplied with 

electrical box)

cUL Listed 

electrical 

box

120V Wires

Washers

Supply wires

Downrod

Hanger pin

Lock pin

Set screws

Canopy

Canopy cover

Coupling cover

Pin in locked

position

   

Step 8. 

Tighten two set screws on top of the fan 

motor firmly. (Fig. 7)

Step 9. 

Place the downrod ball into the hanger 

bracket socket. (Fig. 8)

Step 10. 

Secure the safety cable to the building 

structure with a wood screw. (wood screw not 
supplied) (Fig. 8)

Figure 5

Ceiling hanger

bracket

Ceiling 

canopy

Canopy 

cover 

Safety cable

Содержание Mendocino UHP9010
















Отзывы: